A flange coupling has an outside diameter of 200 mm and connects two 40 mm shafts. There are four 16 mm bolts on a 140 mm bolt circle. The radial flange thickness is 20 mm. If the torsional stress in the shaft is not to exceed 26 MPa, determine the shearing stress in the bolts if uniformly distributed. A. 8.5 N/mm2 B. 5.8 N/mm2 C. 6.5 N/mm2 D. 7.5 N/mm2

Q: A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Detennine…

A: Given The outside diameter of hollow steel tube is D=138 mm. The inside diameter of tube is d=120…

Q: Question 1 B 900 mm 80 mm -40 mm T A The magnesium tube is bonded to the steel rod. Part A If the…

A: Shear stress of magnesium = 45 MPaShear stress of steel = 75 MPaModulus of rigidity magnesium = 18 ×…

Q: 2. A linkage to an aircraft landing gear is shown. • The 40-kN force acting on the wheel has a line…

A:

Q: A 88-N-m torque is applied to a hollow shaft having the cross section shown. Neglecting the effect…

A: The torque applied is

Q: 30 mm 600 mm 36 mm T = 500 N-m с 900 mm 5 Two solid steel shafts are fitted with flanges that are…

A: The rotation of the flange with respect to other flange is φb=1.5°=0.02618 rad. The applied torque…

Q: A flange bolt coupling consists of six ½” diameter bolt spaced evenly around a bolt circle of 14”…

A: Given that: six 1/2 inch bolts are evenly spaced. Bolt circle diameter is 14 inches. Allowable…

Q: A flanged bolt coupling is used to connect a solid shaft 110 mm in diameter to a hollow shaft 100 mm…

A:

Q: Each of the four links in Figure 3 has an 8x36mm uniform rectangular cross section and each of the…

A:

Q: 3. Determine the length (m) of the shortest 2-mm-diameter bronze wire which can be twisted through…

A: Givend=2mmθ=2 turns=2×360o=2×360×π180=12.566 radτallow=70MPaG=35GPa=35×103 MPa

Q: Determine the length of the key to be used based on the compression.

A: Given Data Width of the key b = 32.5 mm Height of the key h = 22.5 mm Diameter of the shaft d = 125…

Q: The bolted connection carries a load as shown. What is the minimum size of the bolt if the allowable…

A:

Q: The steel jacket CD has been attached to the 40-mm diameter steel shaft AE by means of rigid flanges…

A: Given Data

Q: Link AB, of width b= 2 in. and thickness t = in., is used to support the end of a horizontal beam.…

A:

Q: An aluminum rod AB of diameter 2.8 inches is connected to a lever of length L = 5.6 feet. Consider…

A: Given:diameter, d=2.8 inL=5.6 ftheight, H=3.4 ftTorsional shearing stress of aluminium, ζa=1111 psi

Q: II. Solve the problems below: 1. A rigid bar, pinned at O, is supported by a steel spring at A and a…

A: Answer: (a) The shearing stress in steel spring is 2.87 MPa. (b) The shearing stress in bronze…

Q: A flanged bolt coupling consists of six - ½ inch steel bolts evenly spaced around a bolt circle of…

A: Given data: nst=6nal=4dst=12indal=34inRst=6 inRal=4 inT=200 in.lb Need to determine the stresses in…

Q: A 35-mm diameter rivet joins the plates that are each 150 mm wide. The allowable stresses are 200…

A:

Q: Q3) A bronze helical spring composed of 10 turns of 1.0-inch diameter wire on a mean radius of 3…

A: GIVEN:no. of turns, N=10diameter, D=1inradius, R=3inload, P=750lbG=6X106psithere given that the…

Q: Determine the shearing stress in the pin with diameter equal to 25 mm. Express the answer in MPa.…

A:

Q: PROBLEM NO. 2 A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in…

A: Given data: ◆ The bolt circle diameter: D = 250 mm ◆ The number of bolts: n = 12 bolts ◆ The…

Q: 5. A transmission shaft has a torsional stress of 7,000 psi. If the diameter of shaft is 1.5 inches,…

A:

Q: B. Two springs were attached in a series as shown. The maximum Shearing stress of the spring is…

A: Given data: τ=200 MPaG=80 GPa Need to determine the maximum allowable load and total elongation.

Q: Problem # 2: The frame carrying a 425-kg load is supported by roller at D and smooth pin at A.…

A:

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A: if you have any doubts please comment

Q: 16 kN 125 mm 3. The two boards are joined by plywood splices that are fully glued on the surfaces in…

A:

Q: 1. A circular piece of wood, 90mm in diameter, is used as a compression block. Determine the axial…

A:

Q: A 22.2 mm diameter bolt having a diameter at the root of the threads of 18.6 mm is used to fasten…

A: Given data as per question diameter of bolt =22.2 mmRoot diameter of thread =18.6 mmLoad =34…

Q: Four bolts used to lap joint two steel plates together. Tensile force on the plates is 66.7 kN.…

A: Given data: F=66.7 kNn=4τAllow=68.9 MPa Need to determine the diameter of the bolt.

Q: Each of the four links in Figure 3 has an 8x36mm uniform rectangular cross section and each of the…

A:

Q: determine the bolt diameter required in mm. (b) If the shaft is made of the same material as the…

A:

Q: de diameter of 250 mm. The pole is subjected to es uniformly from 800 N/m at the base to 1200…

A:

Q: A steel (G = 12,000 ksi) shaft is bolted with end flanges to wall supports at A and C. The pipe has…

A:

Q: Handwritten solution with Fbd. No Chatgpt.

A: Step 1:  Step 2:   Step 3:

Q: A flange bolt coupling consist of 8-12.7mmꬾ steel bolts on a circle diameter of 304.80mm & 6-12.7mmꬾ…

A:

Q: 4. A line shaft with a power of 100 kW at a speed of 1,200 rpm, had a rectangular key in its pulley…

A: Power,  P=100kWmax. shear stress for shaft τshaft=40N/mm2max. shear stress for key τkey=30N/mm2width…

Q: Determine the maximum shearing stress in a helical steel spring composed of 20 turns of 20-mm…

A:

Q: Two steel springs are arranged in series. They support a load P. The upper spring has 12 turns of 25…

A: The number of turns in upper spring, n1 = 12The diameter of the wire of upper spring, d1 = 25 mmThe…

Q: The member BD is attached to a rod at B, to a hydraulic cylinder at C, and to a fixed support at D.…

A: According to the question data τallow=40ksi at point D σAllow=60ksi =tensile stress in the rod AB we…

Q: The members of the structure in Fig. weigh 200lb/ft. Determine the smallest diameter pin that can be…

A:

Q: 3. A machine shaft is supported on bearings 1 m apart is to transmit 190 KW at 300 rpm while…

A:

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.