The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. The modulus of rigidity is 3.7 × 106 psi for aluminum and 5.6 × 106 psi for brass. Take T = 13 kip·in. a) Determine the maximum shearing stress in cylinder AB. b) Determine the maximum shearing stress in cylinder BC.

The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. The modulus of rigidity is 3.7 × 106 psi for aluminum and 5.6 × 106 psi for brass. Take T = 13 kip·in. a) Determine the maximum shearing stress in cylinder AB. b) Determine the maximum shearing stress in cylinder BC.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The shaft assembly shown below is fixed at its ends A and D. It consists of an aluminum (G = 30 GPa) segment AB rigidly connected to a steel (G= 75 GPa) segment BCD. Both segments have a 80-mm diameter. If the shaft is subjected to a torque 7 of 9 kN-m applied at C, determine The reactions at A and D; a) b) The angle of twist at point B; The maximum shear stress in the shaft. 300 mm -Aluminum 600 mm Steel C 300 mm
1. The member BD is attached to a rod at B, to a hydraulic cylinder at C, and to a fixed support at D. The bolt used at D acts in double shear and is made from a steel for which the maximum allowable shearing stress is Tallow = 40 ksi. The rod AB is made of a steel for which the maximum allowable tensile stress is Oallow = 60 ksi. The upward hydraulic force applied at C is 12 kip. 1) Calculate the minimum diameter of the rod AB. 2) Calculate the minimum diameter of the bolt at D. B FAB 12 kip 8 in. FBD
The members of the structure in Fig. weigh 200lb/ft. Determine the smallest diameter pin that can be used at A if the shearing stress s limited to 5000 psi. Assume single shear. 4R + 3t
A load P is supported by two (2) concentric steel springs. The inner spring consists of 40 turns of 20 mm diameter wire on a mean diameter of 150 mm, the outer spring has 30 turns of 30 mm diameter wire on a mean diameter of 200 mm. Use G= 83000 MPa. a) Determine the maximum load that the inner spring could carry so as not to exceed a shearing stress of 140 MPa. b) Determine the maximum load that the outer spring could carry so as not to exceed a shearing stress of 140 MPa. c) Determine the maximum load that the spring could carry.
please indicate illustration
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 11 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 8 mm in diameter. Assume a = 530 mm, b = 265 mm, h = 380 mm, and 8= 65°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax= (1) i B b C /9 KN h P
3. A solid bar having a diameter of 160 mm is to be replaced by a rectangular tube having cross- sectional area of 150 mm x 310 mm to the median line of the cross-section. (a) Determine the required thickness of the tube so that the maximum shear stress in the tube will not exceed the maximum shear stress in the solid bar. (b) Determine the shear stress in the tube . If it is subjected to a torque T = 15 kN-m and a thickness of 10 mm. and (c) Determine the angle of twist in degrees of the tube if the length of the tube is 1000 mm and the shear modulus is 75 GPa. Thickness of the tube is 10 mm and the torque T = 15 kN-m.
a. Compute the maximum shearing stress at point B in MPa. b. Compute the normal stress at point B in MPa. c. Compute the maximum compressive stress at point B in MPa. d. Compute the shearing stress at point A in MPa e. Compute the normal stress at point A in MPa.
Problem 1: The lap joint shown in the figure is fastened by nine 20mm diameter rivets. Each plate has a thickness of 25mm and width of 250mm. Assuming that P = 50kN. a) Determine the shearing stress in each rivet b) Determine the bearing stress in each plate c) Determine the maximum average tensile stress in the most stress part of each plate.
1
3. As shown, a vertical 200 lb force is applied to the gear and shaft assembly at point D. Shaft ABC is solid and has a 0.5 in. radius. (you may use a coordinate system of your choice, as long it's correct.) y 2.5 in. 10 in. D H B Z X 200 lb a) Determine the state stress (all stresses with their indices) at point H on top of the shaft. b) Determine the principal stresses and max shear stress at point H.