A flange bolt coupling consists of 8-12mm diameter steel bolts on a bolt circle 350mm in diameter and 6-12mm diameter steel on a concentric bolt circle 250mm in diameter. What torque in KN-m can be applied without exceeding a shearing stress of 30 MPa in the bolts? O a.7.865 O b.6.568 Oc.6.867 Od.8.756

Q: A static shaft is subjected to torques at A, B, and C. It has a diameter of 58 mm and is made from…

A: The magnitude of angle of twist is The length of shaft  1 is The length of shaft 2 is The diameter…

Q: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve CD…

A: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksiThe sleeve CD is…

Q: The shaft ABCDE is under equilibrium. Determine the internal torque in section (3).

A: Given data, TE = Torque at E = -11 N-m (Cross-section is twisted in clockwise direction from right…

Q: A 88-N-m torque is applied to a hollow shaft having the cross section shown. Neglecting the effect…

A: The torque applied is

Q: Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner…

A: Given data:- a hollow circular steel shaft outer diameter =4 inch inner diameter =3 inch  TB…

Q: (5) When the bar subjected to torque, the maximum shear stress occur at.. O A. External surface of…

A: When a bar is subjected to the torque, the shear stress will be produced in the bar.

Q: A power source at C actuates valves at A and B through a long round steel control rod. A torque of…

A:

Q: Q.2) Three solid Brass (G = 44 GPa) shafts along with two sets of meshing gears are used to form…

A:

Q: Using Tall = 8.7 ksi and knowing that G= 5.6 x 106 psi, determine for each of the cold-rolled yellow…

A:

Q: The steel jacket CD has been attached to the 40-mm diameter steel shaft AE by means of rigid flanges…

A: Given Data

Q: A hollow thin-wall member with a uniform thickness shown below is subjected to a torque T. We are…

A: The shear stress flow through complete section is given below,

Q: A 2 in 1-in dia. B in 1½ in Fy 2-in dia. 6 in 5 in For the cantilevered handle shown, the force Fy…

A: 2. Loads at Point BMagnitudes and Directions of Forces and/or Moments at Point B:To balance the…

Q: The solid rod AB has a diameter dAB5 60 mm and is made of a steel for which the allowable shearing…

A: Given Data: The diameter of the rod AB is: dAB= 60 mm The outer diameter of the pipe CD is: dCD=90…

Q: Shafts A and B are made of the same material and have the same cross-sectional area, but A has a…

A:

Q: A 2000 in-Ibf torque acts on a hollow shaft with an outer diameter of 2 in and an inner diameter of…

A: Torque, T=2000 in.lbfOuter diameter of shaft, do=2 inInner diameter of shaft, di=1.75 in

Q: The composite shaft shown consists of a solid brass segment (1) and a solid aluminum segment (2)…

A: Given:d1=15 mmL1=235 mmG1=4 GPad2=24 mmL2=165 mmG2=39 GPaT=270 N.m

Q: 4

A: Please see the attached image for the answer.Explanation:

Q: Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner…

A:

Q: angle of twist (a) between A and B, (b) between B and C, um (c) At C

A:

Q: 15. Given a front hand brake of a bicycle. The applied force, P = 70 N and the equivalent area and…

A:

Q: Using Tall = 7.95 ksi and knowing that G= 5.6 x 106 psi, determine for each of the cold-rolled…

A: Given dataAllowable shearing stress=7.95 KsiG=modulus of rigidity=L=Length of the bar= 16 inFind,1)…

Q: The compounded A-36 steel shaft (GA-36 steel = 75 GPa) is fixed to the wall at A and is subjected to…

A: given data:A 36-steel shaft Modulus of rigidity = 75 GPalength of AEB = 2m length of BDC = 1m torque…

Q: A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm…

A: The angle of rotation: The angle at which the fixed end rotates with respect to the free end is…

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.