Answered: a) Find the rotation at point B of the…

a) Find the rotation at point B of the beam using Finite Element Method. b) Find the stress resultants (M and T) at point D.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a) Find the displacements at point C of the frame using Finite Element Method. b) Draw the stress resultant diagrams (M, N, T). 70[kN]| 50 kN / m 30 (cm) B 60(cm) 1.5 m) E=28 GPa. 1.5(m) 9 (m)
Figure Q2(a) shows a cantilever beam that is subjected to a pure bending moment M = 3kN.m about the neutral axis (N.A) and the cross-section of a beam is shown in Figure Q2(b). Determine: (a) The moment of inertia about the neutral axis, InA. (b) The bending stress acting at point B and state whether it is in tension or compression. (c) The bending stress acting at point C (d) The maximum bending stress in the beam. M Figure Q2 (a) 20 mm B 150 mm C N 20 mm 150 mm 20 mm 250 mm Figure Q2 (b)
tate of Stress Caused by Combined Loadings Learning Goal: To use the superposition principle to find the state of stress on a beam under multiple loadings. The beam shown below is subjected to a horizontal force P via the rope wound around the pulley. The state of stress at point A is to be determined. 100 mm 15 mm 20 mm 200 mm 150 mm f 20 mm The dimensions are di - 2.15 m. d₂ = 0.5 m. -0.85 m d-285 mm and r= 150 mm The applied force has magnitude P=4.5 kN Part A-Support Reactions and Internal Loading C₁, C₂=₁ N=, V = ₁ M = Determine the support reactions C, and C, and the internal normal force, shear force, and moment on the cross-section containing point A. Express your answers, separated by commas, to three significant figures. ► View Available Hint(s) Submit Part B- Properties of the Cross-Section A= I= Q = Submit VAX IT VOC JA=.TA= What are the cross-sectional area, moment of inertia with respect to the neutral axis, and first moment of the area with respect to point A for the…
A rigid beam is supported by bar DE. If the vertical displacement of point D is to be less than 0.1 in, what is the minimum cross-sectional area of bar DE? Assuming that area, what is the stress state at p in the coordinate system shown? A = σ= in² ksi 12 ft A Balance Laws 800 lb 5 ft / 16 ft) = B 800 lb 5 ft Bar DE: E=30000 ksi V = 0.29 point p C 6 ft E D (800) (5)+ (80.
Q2) B) The steel rod having a diameter of 2Z mm is subjected to an internal moment of 4Y0 Nm as shown in Figure Q2(b). Take: Z =1 Y = 0 i) Determine the stress created at points A, B, and C. ii) Sketch a three-dimensional view of the stress distribution acting over the cross section. Note that moments of inertia for the circular area can be determined by I= (ar' )/ 4. y A B. M = 4Y0 Nm 45° Radius = 0.5(2Z) mm Figure Q2(b)
3. The plane stress is shown on the element. Use Mohr's circle. 1) Determine the principal stresses and corresponding orientation of the element from the position shown. 2) Determine the in-plane maximum shear stress and corresponding orientation of the element from the position shown. 3) Determine the state of stress on an element oriented 45° counterclockwise from the position shown. 90 MPа 60 MPа 20 MPа
The horizontal beam is supported by a pin at A and the pin-connected link BC. It has a uniformly distributed loading w = 7.0 kN/m as shown in the figure. All the pins are in double shear and have a diameter of 20 mm. Determine the max shear stress in the pin at A. Input your answer as a value only in MPa to one decimal place without +/- sign. W 1.5 m 2 m B 1 m
The truss ABC shown in the figure is subjected to a horizontal load P=40 kN. The two bars are identical with cross-sectional area A= 400 mm^2 and modulus of elasticity of 200,000 MPa. Neglecting the weight of the truss. A. Determine the stress of member BC.B. Determine the strain energy U of the truss. C. Determine the horizontal displacement of joint B by equating the strain energy of the truss to the work done by the load.
A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has the following equation for the vertical displacement: w (2) = - + F 48 %3D The value of E is 200,000 Nmm² and the values of ly is 20 x 10° mm“ The maximum value of z for the beam cross section is +20 mm What is the maximum tensile stress in the beam at the point when x = 86 mm?
A symmetrical beam of length 300 mm is loaded with a force of 414 N downwards (positive z) and has the following equation for the vertical displacement: F w (x) = E, ( - +4) %3D Ely 8. The value of E is 200,000 Nmm 2 and the values of ly is 20 x 106 mm4 The maximum value of z for the beam cross section is 20 mm What is the maximum tensile stress in the beam at the point when x = 86 mm? Express your answer in Nmm2, as a number to 2 dp, without the units.
3. Two beams are supported as shown in the diagram below, each 150mm x 200mm x 4 meters. Beam CD is a cantilever beam carrying a uniformly distributed load of 4 KN/m freely supported on beam AB. Beam AB is freely supported on each ends. E = 13.8 GPa for both beam. Neglect the weight of the beam. a. Compute the reaction at D. b. Compute the deflection at D. c. Compute the bending stress of beam CD. 4kN Im 4m 4m
Please show complete solutions. Considering EI is constant and the value of P is 425kN, calculate the following using Conjugate beam method : A. What is the value of the reaction at point B in the real beam? B. What is the value of the reaction at Point A in the conjugate beam? C. DISPLACEMENT AT C. D. DETERMINE SA SLOPE AT B.