a) Draw the Mohr's Circle associated with its original state of stress. Calculate and label the dimensions depicting x, y, and Txy. b) Draw the Mohr's Circle associated with its transformed state of stress. Calculate and label the dimensions depicting x, y, and Tx'y' along with the angle 0. c) If the element were instead to be rotated 50° counterclockwise (from its original orientation), draw the resulting Mohr's Circle. Calculate and label the dimensions depicting ', ', and Tx'y' along with the angle 0.

a) Draw the Mohr's Circle associated with its original state of stress. Calculate and label the dimensions depicting x, y, and Txy. b) Draw the Mohr's Circle associated with its transformed state of stress. Calculate and label the dimensions depicting x, y, and Tx'y' along with the angle 0. c) If the element were instead to be rotated 50° counterclockwise (from its original orientation), draw the resulting Mohr's Circle. Calculate and label the dimensions depicting ', ', and Tx'y' along with the angle 0.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. For the roof truss shown in Figure 3, determine the force present in ele- ment GH and in each element located to the right of GH. Also, establish whether the elements are in tension or compression. (I suggest you start from node M applying the method of nodes until you get to element GH) -2.4 m--2.4 m-1.2 m-2.4 m--2.4 m--1.2 m- 1.5 kN 1.5 kN 1.5 kN 1.5 kN D VI 1.5 kN 1 kN В 2.5 m E K 1 kN 1m H M F
The state of stress at a point in a member is shown on the element. Determine the absolute normal stress component acting on the inclined plane AB in ksi.
The state of stress at a point in a member is shown on the element. Determine the principal normal stresses and their orientation and the maximum in-plane shear stress and their orientation. Draw Mohr’'s circle and Show results on properly oriented elements. -60 30 -50 40 -40 T-30 30 30 -20 40 30 -10 -60 -50 -40 -30 -20 -10 30 40 50 10 20 бо 10 20 30 40 50 60
A differential element on the bracket is subjected to plane strain that has the following components: , strain at x = 250 x 10-6, strain at y = 300 x 10-6, strain at x y= -500 x 10-6. Use the strain-transformation equations and determine the normal strain strain x' in the x' direction on an element oriented at an angle of 35°. Note, a positive angle is counter clockwise.
An element in uniaxial stress is subjected to a tensile stress of 49mpa in x-direction. Determine the stress acting on element oriented at an angle of -27degree celcius from x-axis(clockwise direction)
16 Yield point is the boundary in the stress-s train diagram where stress loses its prop ortionality with strain.( 17 True 18 False Strain is the ratio deformation over origin al length.( True False The value of stress can be unitless. True False
A rectangular tetrahedron has six sides of length 9 cm. If a force of 600 N is applied along edge BC as As shown, determine the moment of the 600-N force about edge OA. A B 600 N
Fourier series: simply supported beam deflection under trapezoidal load
1. For the roof truss shown in Figure 3, determine the force present in ele- ment GH and in each element located to the right of GH. Also, establish whether the elements are in tension or compression. (I suggest you start from node M applying the method of nodes until you get to element GH) -2.4 m--2.4 m-1.2 m-2.4 m--2.4 m--1.2 m- 1.5 kN 1.5 kN 1.5 kN 1.5 kN D VI 1.5 kN 1 kN В 2.5 m E Ук 1 kN 1m H F Figura 3. Cercha 3. 2.Determine the force in the elements ED, EH, and GH of the reinforcement (see Figure 4), and establish whether the elements are in tension or compres- sion. (Use the method of sections). Figura 4. Cercha 4. 50 kN 40 kN -2 m -2 m- -2 m- 1.5 m -30 kN 1.5 m B 40 kN 1.5 m
i need the answer quickly
answer quickly
Determine principle stress and angles