A factory is supplied with a 3-phase 6600V 60 hz transmission line. The factory has the following loads. Load A : 1.2 MVA at 0.8 lag p.f. Load B: 2 MVA at 0.75 lead p.f. Load C : 0.8 MW at unity p.f. To correct the overall p.f to 0.99 lag at full load , requires a wye connected capacitor bank. Determine the capacitance per phase of the bank

A factory is supplied with a 3-phase 6600V 60 hz transmission line. The factory has the following loads. Load A : 1.2 MVA at 0.8 lag p.f. Load B: 2 MVA at 0.75 lead p.f. Load C : 0.8 MW at unity p.f. To correct the overall p.f to 0.99 lag at full load , requires a wye connected capacitor bank. Determine the capacitance per phase of the bank

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

answer C and E only
V1 ZT Z2 V2 V3 Z5 Z3 Z4 Figure 18.4 See Figure 18.4. In a general bridge circuit such as this, what condition will result in a balanced bridge? Z1Z4 = Z2Z3 Z3 = Z4 O ZĄZ3 = Z2Z4 O Z1Z2 = Z3Z4
please explain each part on paper thank you i will like
For the circuit shown below, detemine the voltage of the -j10 2 capacitive reactance. -jsn jl0n 0.5L-90 ILOAT j102 js 2 102 ( 552
supply 3. Three circuits A, B and C are connected in series across 350 V supply. The voltage across circuit A is 80 V lagging the voltage by 330 and the voltage across circuit C is 140 V leading the supply voltage by 48°. Determine the voltage circuit B and its phase displacement from the supply voltage using wave and vector solution. across 4. Draw the phasor and wave diagram of the following sinusoidal current:
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
The e.m.f. 's from four generators are e = 4 7sin@t e = 2 cos ot, e =/7 cos(@t + 90° ) and 1 3 = 5/2 sin(ot – 90° ). The alternators are connected in series. e4 18. Find the rms value of the resultant e.m.f A 5.0 В 4.0 C 2.5 D None of the above. 19. If the resultant e mf is expressed in the form e = Asin(ot + B). Find Bin degrees. A 53.1 в 369 С -53.1 D -36.9
If the phase lag less than zero means that the output behind the input. * False true
Three Impedances each of (6 - j28)2 are connected in mesh across a three-phase 415V ac supply. Determine the phase current, line current, active power, reactive power and apparent power drawn from supply. phase current (Ip) Line current real power reactive power Apparent power
Design the circuit in Fig. 1, such that the quiescent current is 0.5 mA and the voltage drop from the drain to ground is 1.0 V. The MOSFET parameters are K, = 0.25 mA/V² and VTN = 1.4 V. Assume that the MOSFET is biased in saturation region. P+5V Rp VD RG = 47 kQ Rs -8V Fig. 1
Solve 9
Prob. I and Vc For the following RMS phasor circuit, a coworker has determined values for 50 Ohms 50 Ohms i,- 225 2253.13° = 190.92 + 254.56 VRMS R1 + R2 Vc = 237.17/26.565° = 212.13+ 106.07 VRMS 100 2 -3Z98.13° =-0.4243 + J2.970 ARMS C -j60 Ohms For this problem provide at least 3 digits of precision for the answers. The results for the following calculations are to be answered in - a) Find the current I b) Determine the real (P) and reactive(Q) power DELIVERED by the source c) Determine the real (P) and reactive (Q) power ABSORBED by each impedance ( resistors R1 and R2, inductor and capacitor). The values for P and Q can be positive or negative. Remember S =P+jQ, so do not include the j with your answer for Q. Each of these answers will require two parts. For the phasor a magnitude and angle will be needed. For the powers, The real power P and the reactive power Q are required.