plz do step by step A designer is required to achieve a closed-loop gain of 10 ± 0.1% V/V using a basicamplifier whose gain variation is ±10%. What nominal value of A and B (assumedconstant) are required?

Answered: Image /qna-images/answer/8f1f327e-05ec-457c-b98e-04fa23e0dbf5.jpg

Answered: A designer is required to achieve a…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q3. Design a DC/DC buck converter (as shown in Figure Q3) for an input voltage of 12V and an output of 5V at 20A. Assume a switching frequency of 10kHz. Constrain the inductor ripple current to be 10% of the input current and limit the output voltage ripple to 50mVp-p. a) Explain the working mechanism of the converter by sketching equivalent circuit diagrams when the switch Q is ON and OFF, Calculate the duty cycle of the switch. Find the ripple of the inductor current. Calculate the required inductance and capacitance. Sketch the waveform of the output voltage. Is the converter works at continuous conduction mode CCM? If so, give proof of that b) c) d) e) f) g) If the load current varies between 0 and 2A, what is the value of the duty cycle range and at what operating condition? DA L C² Figure Q3 DC/DC buck converter. R
Describe this woofer it is Truvox 1225?
Consider a buck converter with the controlled switch as MOSFET and the uncontrolled switch as diode, the input to buck converter is 60 V. The MOSFET is turned on and off for 20 msec and 10 msec periodically. Assuming ideal components, the output voltage of the buck converter is
c) A buck converter with constant frequency peak current mode control has Vs = 28V, V = 20V, L = 301uH, fs = 100 kHz. Find the ramp slop for the optimum compensation and the peak compensation voltage. %3D
Consider the circuit in Figure A4. (a) Explain its operation with the aid of diagrams. (b) Assume that R₁ = 21 kQ, Vref = 1.2 V, Vs = +12 V and -Vs = -12 V. Determine a value for R₂ to obtain a maximum threshold voltage of Vth = 5.25 V. (c) Sketch the output voltage signal in time for a sinusoidal input signal of peak voltage 3.5 V and frequency 2 kHz. R1 R2 Vout Vref Vin +Vs -Vs Figure A4
What is the differential gain of the differnce stage of the instrumentation apmplifier? What is the overall differnential gain of the instrumentation apmplifier?
3) Consider the Zener-diode voltage regulator shown below. Suppose you design this circuit to drive (supply) a load resistance RL. The supply voltages to the op-amp are +15 V and -15 V (not shown). a) What is Vout? b) If R = 1 k 2, what is the smallest R, that the circuit can handle without "sagging" the output voltage? c) What should be the power rating of the resistor R? Be explicit about your assumptions. +15 V R Vout IN4738 CS Scanned with CaScanner
1. The DC-DC converter has several circuit configurations. a) (Draw a simple connection of IGBT switch, diode and inductor that can discriminate between Buck, Boost and Buck-Boost converter circuits respectively.) b) ('A Boost converter produces an output voltage, Vo that is more than or equal to the input voltage, Vi. Based on this statement develop the equation for the relationship between Vo Viand D. where D represents the duty ratio. You can use any suitable diagram to illustrate your answer.)
3c
Drive the expression for the average output voltage of a single phase full converter and draw the waveform of output voltage. please explain in details
1c
Ex) A standard two-junction thermocouple configuration is being used to measure the temperature in a wind tunnel. The reference junction is held at a constant temperature of 10 °C. We have only a thermocouple table referenced to 0 °C. Determine the output voltage when the measuring junction is exposed to an air temperature of 100 °C.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

A designer is required to achieve a closed-loop gain of 10 ± 0.1% V/V using a basic amplifier whose gain variation is ±10%. What nominal value of A and B (assumed constant) are required?