(ii)Determine the distance between the location of the hydrostatic force andthe bottom surface of the tank.(iii) From your working on Q2(a)(i) and Q2(a)(i), explain how the circularcross-section area of the tank affects the hydrostatic force magnitude andthe location of the hydrostatic force. A cylindrical tank with its axis horizontal has a length of 6 m and the ends ofthe tank are vertical planes, as shown in Figure Q2 (a). The vertical pipe of 0.2m in diameter is connected to the top of the tank. The tank and the pipe are filledwith ethyl alcohol to a level of 1.5 m above the top of the tank. The diameter ofthe tank isa(a)2.0 mOpen surface1.5 m0.2 mOFBottom surface of the2.XX тcylindrical tankFR6 mFigure Q2 (a)

Answered: Image /qna-images/answer/adb7d89f-d079-4bd7-a194-3d99a4e3b2da.jpg

Answered: A cylindrical tank with its axis…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The tank is filled with oil (S. G.= 0.9) and water. Determine the height of the mercury (S.G.= 13.55) in the tube. 0.6 m D B 0.5 m h' = 0.3 m
di de= Do Р 45° An involute pump casing is approximated as a toroidal shell as shown in the figure above. It has an internal cross-sectional diameter of d; = 490 mm, an overall external diameter of Do = 1420 mm, and a wall thickness of 4.7 mm. Point A is located at mid-thickness of the wall. (a) Express and in terms of the internal pressure p. Enter only the numerical value of the coefficient associated with p. Р A (b) Determine the maximum internal pressure the shell can hold, such that the Tresca stress intensity at point A does not exceed two-thirds of the yield strength oy = 250 MPa. MPa
A rectangular open tank is 6m long, 2m deep and 2m wide is containing water up to 1m height. If the tank is subjected to horizontal acceleration of 3 m/s2, find (i) angle of water deformation on the surface (θ) (ii) force on each end during acceleration (γ = 9790 N/m3)
The angular velocity wac = 5.6° per second. Determine the angular velocity of the hydraulic actuator BC in deg/s. L = 1.38 m 2L2 = 1.15 m 2L2 - Li --- L2 -
B) The pressure in the tank at B is 500 kPa, as shown in fig.(5). If the differential elevation of the oil is h = 2.25 m, determine the pressure at the closed valve A. Take po=900 kg/m. If water is replaced by the same oil in the tube, what will be the pressure at A? Oil 0.5 m 0.75 m 2 m Water D 3.5 m Water B Fig.(5)
3.40 WP To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (a) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (ks = 35 W/m · K) has an inside diameter of Di1 = 150 mm and wall thickness t; = 10 mm while the outer steel pipe has an inside diameter of Di.2 = 250 mm and wall thickness to = t;. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (k, = 0.075 W/m K) between the two pipes does not exceed its maximum service temperature of Tp,max = 70°C. The ocean water is at To,0 = -5°C and provides an external convection heat transfer coefficient of h, = 500 W/m² · K. The convection coefficient associated with the flowing crude oil is h; = 450 W/m2 . K. (b) It is proposed to enhance the…
1) The buoyant force acting on the plate is equal to a the mass of the plate times distance of the plate from the free surface b the weight of the plate c the weight of the liquid displaced by the plate 2) The hydrostatic force acting on a circular surface always passes through the center of the circle. True or False 3) Which of the following situation is UNSTABLE? a,b,c?
2
1500 KN 800 mm 70 mm d) Determine the new thickness of the bar in mm e) Determine the percentage change in the total volume of the bar 100 mm 1500 KN
A large container of benzene is transported on the truck. Determine the level in each of the vent tubes A and B if the truck accelerates at a = l .5 m / s^2 When the truck is at rest. hA = hB = 0.4 m.

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS