B) The pressure in the tank at B is 500 kPa, as shown in fig.(5). If the differential elevation of the oil is h = 2.25 m, determine the pressure at the closed valve A. Take po=900 kg/m. If water is replaced by the same oil in the tube, what will be the pressure at A? Oil 0.5 m 0.75 m 2 m Water 3.5 m Water Fig.(5)

B) The pressure in the tank at B is 500 kPa, as shown in fig.(5). If the differential elevation of the oil is h = 2.25 m, determine the pressure at the closed valve A. Take po=900 kg/m. If water is replaced by the same oil in the tube, what will be the pressure at A? Oil 0.5 m 0.75 m 2 m Water 3.5 m Water Fig.(5)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The distance Ah is the height of the liquid in the manomoter above the heavier liquid in the tank. D 10 cm Water Ah = ? B C 20 cm S= 3.0
Compute the magnitude of the resultant force on the indicated area and the location of the center pressure. Show the resultant force on the area and clearly dimension its location. From the figure
A pump draws water from reservoir A and lifts it to reservoir B as shown in the figure. The loss of head from A to 1 is four times the velocity head in the 50mm pipe and loss of head from 2 to B is 15 times the velocity head in the 100mm pipe. The pump discharge rate us 50 liters per second. Determine the following: A. Power delivered by the pump in KW B. Pressure head at pt. 1 in meter C. Pressure head at pt 2 in meter
4. The siphon shown is 76 mm in diameter. It draws oil from a large tank. The loss of head up to the summit is 6 cm and from the summit to the exit is 23 cm of oil. a. Calculate the exit velocity. b. Calculate the pressure at the summit. 0.6 8.3 76- mm 0 siphon
7. What is the pressure value (PA) needed to achieve equilibrium for the figure shown (kPa)? a. 0.59 c. 1.02 b. 1.02 d. None of all these PA S.G=0.87 30 120 mm
Consider the tank shown in (Eigure 1). Take po = 900 kg/m³, Pu=1000 kg/m³, and pHg = 13 550 kg/m³. 0.6 m 0.8 m 100 mm h 1 of 1 > P Part A Determine the level of water in the tube if the depths of ol and water in the tank are 0.6 m and 0.8 m. respectively, and the height of mercury in the tube is h=0.075 m A Express your answer to three significant figures and include the appropriate units. PA h = 240 Submit + Provide Feedback → OF ? mm Previous Answers Request Answen X Incorrect; Try Again; 4 attempts remaining Next > 1231 AM 0
The initial pressures at A and B are the same at 109 kPa. If the pressure at the liquid at A (SG1 = 2.65) is increased to 134 kPa while keeping the pressure at B constant, determine the new position (Ah, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.69 cm., and the inclination of the tube is 16° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places. SG B Air Yı Δh Ah Mercury
The initial pressures at A and B are the same at 105 kPa. If the pressure at the liquid at A (SG1 = 1.96) is increased to 132 kPa while keeping the pressure at B constant, determine the new position (Δh, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.58 cm., and the inclination of the tube is 11° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places.
Q2: Compute the value of (H) in centimeters such that the pressure at B is 90% of the pressure at point A. If the pressure at A is 79.4 kPa, S.G (oil)=0.89, S.G (mercury)=13.6. SAE 30 oil Gage B Mercury- 6 сm H Water flow 11 cm 4 cm
Consider the pressurized horizontal pipe network consisting of three pipes arranged in series. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 5 cfs and the pressure head at Node A is yA = 200 feet. The temperature of the water is 60° F. a) Determine the friction head loss hfric in feet in Pipe 1. b) Determine the friction head loss hfric in feet in Pipe 2. c) Determine the friction head loss hfric in feet in Pipe 3. d) Determine the pressure head ys in feet at Node B. e) Determine the pressure head yc in feet at Node C. f) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Friction (feet) (cfs) head Нead Pipe (inches) factor f Kpipe loss (feet) Node (feet) 1 16 500 0.011 5 A 200 2 12 1000 0.013 B 3 10 750 0.015 D Node Node Node Node A в D 5 cfs 5 cfs Pipe 1 Pipe 2 Pipe 3
5.13 A horizontal cylindrical tank given in Fig.P.5.13 is filled with water and oil in two different densities. Calculate and plot changes in pressure on the cylindrical surface of the tank. (Hint: Hydrostatic pressure of the oil phase at the top affects the water phase at water-oil interface. In addition, hydrostatic pressure of water phase should also be considered). Tank Dimensions: Diameter : 0.80 m : 2.40 m Length Height of interface : 0.78 m 0.8m Liquids: (1) -(2)* Oil : p= 890 kg/m³ μ-12 cP Water: p= 1000 kg/m³ Figure P.5.13 µ=1 cP
A reservoir contains two different fluids is shown in the figure. The height of the water is 8 m, and the height of the oil (SG = 0.86) is 4 m. a. Determine the density of the oil. b. Determine the pressure between the oil and water in kPa. C. Determine the pressure at the bottom of the reservoir in kPa. OIL WATER