the oil layer contains air under pressure. the bottom, A 2 m thick layer of water of mercury (specific gravity = 13.6) at A closed tank contains 0.5 m thick layer lies above the mercury layer. A 3 m thick layer of oil (specific gravity = 0.6) lies above the water layer. The space above %3D The gauge pressure at the bottom of the tank is 196.2kN/m². The density of water is 1000 kg/m' and the acceleration due to gravity is 9.81m/s. The value of pressure in the air space is

the oil layer contains air under pressure. the bottom, A 2 m thick layer of water of mercury (specific gravity = 13.6) at A closed tank contains 0.5 m thick layer lies above the mercury layer. A 3 m thick layer of oil (specific gravity = 0.6) lies above the water layer. The space above %3D The gauge pressure at the bottom of the tank is 196.2kN/m². The density of water is 1000 kg/m' and the acceleration due to gravity is 9.81m/s. The value of pressure in the air space is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The planar AB cover with a width b = 2 m perpendicular to the plane of the figure is articulated at point B F = 7620 Newton force is applied from point A. Since the weight of the lid is W = 5600 N, find the water depth h for the equilibrium state.Note: Specific mass of water is ρsu = 1000 kg / m3. (figure in image) #fluidmechanics
26. An open-top cylindrical tank 1 meter in diameter is 2.80 m tall. The tank floats in water with a draft of 2.30 meters. Unit weight of lead is 110 kN/m^3 a) What is the weight of tank in KiloNewtons? b) How much lead (in KiloNewtons) must be fastened to the outside bottom of the tank in order make it completely submerged in water? c) How much lead (in KiloNewtons) must be placed inside the tank in order make it completely submerged in water? (Ans. 17.72kN; 4.23kN ; 3.85kN)
Heavy fuel oil flows at Q = 10 gallons per minute (gpm) in a horizontal steel pipe that connects two storage tanks. The diameter of the pipe is D = 1.5 inches. The length of the pipe is L = 100 feet. The depth of oil in the supply tank is 30 feet above the pipe entrance. The temperature of the oil is 60°F, the specific gravity of the oil is s.g.oin = 0.90, the specific weight of the oil is 56.13 lb/ft', and the kinematic viscosity of the oil is 0.00175 ft2/s. The pipe discharges into the bottom of the receiving tank. Neglect minor losses. a) Determine the pressure p at the pipe entrance in pounds per square foot (psf). b) Determine the velocity v in feet per second (fps). c) Determine the Reynolds number Re. d) Classify the flow based on the Reynolds number Re. e) Determine the Darcy-Weisbach friction factor f. f) Determine the friction head loss hfac in feet in the pipe between the two storage tanks. 8) Determine the depth of oil in feet above the exit from the pipe into the second…
At a certain temperature, water rises inside 0.10in diameter capillary tube. How high will it rise if the wetting angle is zero and the surface tension is 0.005 lb/ft?
3Q. At normal atmospheric conditions, approximately what pressure in MPa must be applied to water to reduce its volume by 3%? (Take Ey= 320,000 psi at normal atmospheric conditions)
The surface tension of mercury at 60°C is 0.47N/m. What capillary height in mm will occur in this fluid whe in contact with a glass tube of radius 0.3mm? Use 130° for mercury. O 11.5mm fall O 11.5mm rise O 15.1mm fall O 15.1mm rise
Problem A gas weighs 16 N/m³ at 25°C and at an absolute pressure of 0.25 N/mm². Deter- mine the gas constant and density of the gas.
The initial pressures at A and B are the same at 109 kPa. If the pressure at the liquid at A (SG1 = 2.65) is increased to 134 kPa while keeping the pressure at B constant, determine the new position (Ah, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.69 cm., and the inclination of the tube is 16° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places. SG B Air Yı Δh Ah Mercury
The initial pressures at A and B are the same at 105 kPa. If the pressure at the liquid at A (SG1 = 1.96) is increased to 132 kPa while keeping the pressure at B constant, determine the new position (Δh, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.58 cm., and the inclination of the tube is 11° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places.
Laminar flow normally persists on a smooth flat plate until the critical Reynolds number value is reached. However, the flow can be brought to a turbulent state by adding a roughness to the front edge of the plate. For a particular situation, experimental results show that the local heat transfer coefficients for laminar and turbulent conditions are: Hlam (x) = 1,74.x^-0,5Hturb (x)= 3,98.x^-0,2 Calculate the average heat transfer coefficients for laminar and turbulent conditions for plates of length L = 0.1 m and 1.0 m.
In a two-layer fluid with specific gravities 1.2 and 0.9, a cube of 60 cm is immersed. If the upper and lower halves of the cube are composed of materials having specific gravity 0.6 and 1.4, respectively, then the height of cube above the interface of fluid is cm. [Assume, weight density of water as 9.81 kN/m³] (round off to the nearest integer). Liquid 1: S.G=0.9 S.G=0.6 S.G 1.4 60 cm Liquid 2: S.G=12 30 cm 30 cm
Given the bulk modulus of water B-2.1x1o° Pa= 2.1 GPa, What increase in pressure needs to be applied to the surfaces of a cube of water 1 m on a side to reduce its volume by 4%? O a 0.0600 GPa Ob. None. O c.0840 GPa O d. 0.0700 GPa O e 0.1050 GPa