A cylindrical tank with a large diameter is filled with water to a depth D = 0.368 m. A hole of cross-sectional area A = 5.09 cm² in thebottom of the tank allows water to drain out. (a) What is the rate at which water flows out, in cubic meters per second? (b) At whatdistance below the bottom of the tank is the cross-sectional area of the stream equal to one-half the area of the hole?(a) NumberiUnits(b) NumberiUnits

Answered: Image /qna-images/answer/bac0e046-582b-44ea-ba2f-0d6b499339dd.jpg

Answered: A cylindrical tank with a large…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 12 in. The atmospheric pressure is 14.7 lbf/in2, the specific volume of water is 0.01604 ft3/lb, and the acceleration of gravity is g = 32.0 ft/s2.
Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of reservoirs A and B is 0,15 m³/s and 0,25 m³/s respectively. If the coefficient of friction for three pipes is 0,008, determine the relative elevations of the free surfaces. Neglect all losses other than friction. May you kindly resend the answers in a different format as they appear blank??
There is a cylindrical water tank (diameter D and depth h) with attached circular pipes having diameters shown in the figure. Velocity is assumed uniform across the circular pipes. (a) If the constant o is 1, determine the value of the constant 3 for which the water level h remains unchanged over time. (b) For a = and ß = 2, compute the rate at which the water level changes, which is d. Express the answer as a function of U, d, and D. Indicate whether the tank is filling or emptying. D U ↓d NIC BU QU
Water with density of 1000 kg/m^3 flows through a horizontal pipe (in the x-z plane) bend as shown. The weight of the pipe is 350 N and the pipe cross-sectional area is constant and equals to 0.35 m^2. The magnitude of the inlet velocity is Section (1) 4 m/s. The absolute pressures at the entrance and exit of the bend are 210 kPa and 110 kPa, respectively. Assuming the atmospheric pressure is 100 kPa and neglecting the weight and viscosity of the water , find the following: Control volume The mass flow rate is 180° pipe bend Section (2) The exit velocity is The force (in the z-axis direction) acting on the fluid is
A U-shaped tube is filled with water of density 1000 kg/m3 until the level of the liquid is 28 cm above the bottom of the tube. Then oil of specific gravity 0.78 is poured into one branch of the tube until the level of the liquid in the other branch is 34 cm above the bottom of the tube. (g=9.8m/s2) I) Find the level of the oil-water interface in the branch where the oil was spilled II) Find the level of the oil-air interface in the branch where the oil was spilled
The tank below is cylindrical and has a vertical axis. Its horizontal cross-sectional area is 10 m2. The tank has a layer of water under a layer of gasoline (S.G= 0.72). Three holes were drilled in the tank, one at the bottom of the tank, the second hole is in the water layer, 2 m from the bottom. The third hole was drilled 1S 11 in the gasoline layer 5 m from the bottom. The initial discharge velocities from the bottom and the third holes were also recorded as shown in the table below.
Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 10 in. The atmospheric pressure is 14.7 lbf/in², the specific volume of water is 0.01604 ft3/lb, and the acceleration of gravity is g = 32.0 ft/s². Step 1 Patm = 14.7 lbf/in.² g= 32.0 ft/s² Determine the difference in pressure between points a and b, in lbf/in². Does the pressure increase or decrease from point a to point b? Water v = 0.01604 ft³/lb Save for Later Determine the difference in pressure between points a and b, in lbf/in². Pb-Pa = i lbf/in² 4 Attempts: 0 of 4 used Submit Answer
While filling up your car with gasoline, you notice that it takes 3 minutes to dispense 55 liters of gasoline through the 2.5 cm diameter hose. What is the average speed, in m/s, of the gasoline inside the hose?
The water is flowing through a pipe having diameters 40 cm and 21 cm at sections land 2 respectively. The rate of flow through pipe is 45 litres/s. The section 1 is7 m above datum and section 2 is 4.5 m above datum. If the pressure at section 1 is 35 N/cm2. find the following by neglecting losses: (1) Area of cross section of section1(unit in m^2)? 2)Area of cross section of section2 (unit in m^2)? 3)velocity head at section 1 (unit in m) 4)velocity head at section 2 (unit in m) ? 5) difference in datum head (Unit in m)? 6) Pressure head at section 1 (Unit in m)? 7)pressure at section 2 (unit in N/m)?
Oil (density = 842 kg/m³ and kinematic viscosity = 6.2e - 4 m²/s) is being discharged by a 66 mm diameter, 3 m long horizontal pipe from a storage tank open to atmosphere. The height of the liquid above the centre of pipe is 1 m. Disregarding the minor losses, determine (to 4 decimal places): a) the volumetric flow rate of the oil through the pipe m³/s b) the corresponding Re number.
In a horizontal pipe water flows at a rate of 9.1 L/s. Here, the pipe has two sections, one with a diameter of 10.16 cm and the other with a diameter of 5.08 cm, with a gradual smooth reducing section. In this case, a mercury manometer is used to measure the pressure difference. If friction is negligible how would I find the differential height of mercury between the two sections? If the manometer on the 5.08cm pipe section was replaced with a pitot tube how would the reading change? any help would be deeply appreciated
2. The figure shows four cylinders of various diameters filled to different heights with water. A hole in the side of each cylinder is plugged by a cork. All cylinders are open at the top. The corks are removed. Which of the following is the correct ranking of the velocity of the water (v) as it exits each cylinder? B D 2x 2h 2h D/2 (A) VA > VD > vc > VB (B) VA = VD > vc > VB (C) VB > Vc > VA = VD (D) vc > VA = VB = VD

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS