I wish to fill my glass with 200 ml of water from the cooler shown below. Estimate the time (seconds) required to fill my glass if the diameter of the cooler is 45 cm and the diameter of the flow from the cooler is 0.13 cm. List all assumptions clearly (a portion of the points will be based on having a complete and correct list of assumptions). T 41 cm + 41 cm T 31 cm 10 cm

I wish to fill my glass with 200 ml of water from the cooler shown below. Estimate the time (seconds) required to fill my glass if the diameter of the cooler is 45 cm and the diameter of the flow from the cooler is 0.13 cm. List all assumptions clearly (a portion of the points will be based on having a complete and correct list of assumptions). T 41 cm + 41 cm T 31 cm 10 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The velocity distribution in a 0.02 m diameter horizontal pipe conveying carbon tetrachloride (specific gravity = 1.59, absolute viscosity = 9.6 x 10-6 Pa sec) is given by the parabolic equation: v(r)=0.01(0.12- r?), where v(r) is the velocity in (m/s) at a distance r in (m) from the pipe center. What is discharge? O a. 3.13 x-8 m3/s O b. None of the mentioned O c. 1.047 x 108 m3/sec O d. 4.97 x 109 m3/sec
(Q26) A horizontal Venturimeter with inlet radius 110 mm and throat radius of 55 mm is used to measure the flow of water. The pressure at inlet is 20 N/cm2 and the vacuum pressure at the throat is 27 cm of mercury. Find the rate of flow. The value of cd may be taken as 0.9
The pressure differential of oil (with specific gravity of 0.789) flowing through different sections of pipe is 750 Pascals. If the velocity of the oil in the first pipeline section is 1.2 meters per second what is the velocity of this oil in the second pipeline section?
USE 4 DECIMAL PLACES ON YOUR FINALANSWERS DO NOTUSE SCIENTIFIC NOTATIONS NO NEED TO INPUT THE UNITS A Liquid fluid with a density of 1,750 kg/m3 from an elevated 2m open reservoir (P1=0 bars) flows before the pump at 7.5 m/s. The liquid fluid is pumped at an unknown final velacity to a 75 meter elevated tank with a pressure reading of 7.75 Bars. assuming Friction losses is 757.75J and the actual WORK of the pump is 1,933,400J. Calculate the power in HP if the pump's efficiency is just 75% and for every 1,000 kg of fluid per hour.
The pressure in a water tower is 20,674 Pascals (N/m2) higher than at an open faucet. The density of water is 1000 Kg/m3. Use Bernoulli’s equation to determine the velocity of outflow from the open faucet. If the height difference between the top water level in the tower and the faucet is 7.2 meters, then the velocity of outflow is ROUND TO 3 DECIMAL PLACES
A pump 254 mm suction pipe and a 127 mm discharge pipe is used to deliver 52 L/s of water. The suction gage reads 15.6 kPa vacuum and the discharge gage located 100 cm above the suction gage which reads reads 108 kPa gage. Determine the following: 1. The total dynamic head in meter 2. The water power in kW 3. The motor horsepower if the pump efficiency is 76% Choices: 1. 13.856 14. 495 14.409 2. 7.631 7.348 8. 245 3. 12.960 14.935 13.935
Q1. Two pumps with 105.4 cm in diameters characteristics shown in figure below are used in paralel to pump water to the system. Neglecting local losses, calculate total flow rate and pump power. (a) n= 710 d/dak 120 7.5 80m ENPY (2) 6. 105 - 105.4 cm çap S N 4.5 3 90 96.52 cm çap 88% 86% 75 - 88.9 cm çap S4% (1) bom 60 1100 kW 45 750 kW 30 0.25 0.50 0.75 1.00 1.25 1.50 1.75 Debi m/s Note: Pipe is cast iron with 0.6 m in diamater and 1.6 km in length. Fluid is water with density 1000 kg/m³ . ENPY m %68 900 kW
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.Water flows through a schedule-40 pipe that changes gradually in diameter from 6 in (154mm) at point A to 18 in (429 mm) at point B. The volumetric flow rate is 5.0 *3/sec (130 L/s). The respecLve pressures at points A and B are 10 psia (70 kPa) and 7 psia (48.3 kPa). All lossesare insignificant. What are the direcLon of flow and velocity at point A? (A) 3.2 */sec (1 m/s); from A to B(B) 25 */sec (7.0 m/s); from A to B(C) 3.2 */sec (1 m/s); from B to A(D) 25 */sec (7.5 m/s); from A to B
The pressure in a water tower is 27,030 Pascals (N / (m ^ 2)) higher than at an open faucet. The density of water is 1000Kg / (m ^ 3). Use Bernoulli's equation to determine the velocity of outflow from the open faucet. the height difference between the top water level in the tower and the faucet is 9 meters, then the velocity of outflow is
How do I answer this question?
Water flows from a 20-mm-diameter pipe with a flowrate Q as shown in the figure below. What is the approximate diameter of the water stream, d, in units of cm, if the distance below the faucet is, h=2 m, and Q = 0.003 m³ /s? 20 mm O a. 1.83 m b. 2.07 m O c. 3.29 m d. 4.66 m O e. 5.29 m
The velocity is changed from 34.3 m/s to 53.7 m/s in 2.2 s for a fluid of mass 5.2 kg. Then the force applied on the fluid is -_N 3.70 4353.61 208.00 45.85