A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile load of 27,500 N. It must not experience either plastic deformation or a diameter reduction of more than 7.5×103 mm. Of the materials listed as follows, which are possible candidates? Justify your choice(s). Material Modulus of Elasticity(GPa) Yield Strength (MPa) Poisson's Ratio Aluminum alloy 70 200 0.33 Brass alloy 101 300 0.34 Steel alloy 207 400 0.30 Titanium alloy 107 650 0.34

A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile load of 27,500 N. It must not experience either plastic deformation or a diameter reduction of more than 7.5×103 mm. Of the materials listed as follows, which are possible candidates? Justify your choice(s). Material Modulus of Elasticity(GPa) Yield Strength (MPa) Poisson's Ratio Aluminum alloy 70 200 0.33 Brass alloy 101 300 0.34 Steel alloy 207 400 0.30 Titanium alloy 107 650 0.34

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tension test was conducted for a cylindrical specimen of stain-less steel having an initial diameter (D) of 10.85 mm. Calculate the percentage reduction in area if the fracture diameter of the specimen (d) is 6.15 mm. Select one: O a. 68.87% O b. 69.87% c. 66.87% O d. 67.87%
Table Q1 consists of 4 (four) materials with their mechanical properties. The length of a cylindrical rod 380 mm long, having a diameter of 10.0 mm, is to be subjected to a tensile load of 24,500 N. (a) Calculate the stress of the cylindrical rod. (b) Compare with data given in Table Q1 which are the likely materials for the cylindrical rod if it does not experience plastic deformation? Justify. (c) What is the likely material if the elongation is less than 0.9 materials? Justify. Table Q1 Modulus of Elasticity, Yield Strength and Tensile Strength Material Modulus of Yield Tensile Strength Strength Elasticity (GPa) (MPa) (MPa) Aluminum 70 255 420 alloy Brass alloy 100 345 420 Copper 110 250 290 Steel alloy 207 450 550
10. A standard steel specimen of 0.504" diameter elongated 0.0125" in an 8" gage length during a test where it was subjected to a tensile force of 6249 lb. If the specimen's gage length was measured to be 8.0025" after the test was over, what was the permanent plastic deformation? What is the elastic deformation and what is the modulus of elasticity of that metal? r PL AE
Can you answer the questions starting with the yield point and then the rest of the problem?
Explain the most critical loading condition for fuselage central part structure of airliner aircraft. Draw figures of structure elements to resist this loading.
A new high stiffness plastic material has a length of 19.7 inches and a thickness of 3 mm and is being considered for use as a bone fixation plate. When subjected to a tensile load of 10000 N, the material stretches to a length of 19.88 inches. Please find the width of this material, which has a modulus of 4 GPa.
(b) A cylindrical rod made from an unknown metal is 350mm long and has a diameter of 10mm. The rod is subjected to a tensile load. It experiences only elastic deformation and elongates by less than 1.0mm under an applied load of 19,800N. Could any of the four metals listed in the table below could be the unknown metal? If so which ones and why? Material Modulus of Yield Ultimate Elasticity / GPa Strength / MPa Tensile Strength / MPa Aluminium 70 255 420 alloy Brass 100 345 420 Copper alloy Steel 110 250 290 207 450 550
Define the modulus of elasticity?
= Calculate five factors from stress strain curve for polybutadiene? Strees 0.045 0.04 0.035 0.03 0.025 0.02 0.015 0.01 0.005 0 0 10 20 30 Strain 40 50 60
A fuel transportation industry uses a spherical 1045 carbon steel pressure vessel with a diameter of 800 mm and a thickness of 30 mm, covered with a brittle varnish that cracks in the vessel cover when the deformation exceeds 200 x 106. What is the value of the internal pressure that causes the varnish to develop cracks? (Assume E = 205 GPa and v = 0.30). Explain you answer.
2) For a brass alloy, the stress at which plastic deformation begins is345 Mpa and the modulus of elasticity is 103GPa.a) What is the maximum load that can be applied to a specimen with area130mm² cross section without plastic deformation? b) If the original length of the specimen is 76 mm, what is themaximum length to which it can be stretched without causing deformationplastic?