Question 1 You are working on a design team at a small orthopaedic firm. You have been asked to select a cobalt- chrome-molybdenum (CoCr) material that will not experience plastic deformation under a specific mechanical test, as follows... A tensile stress is applied along the long axis of a solid cylindrical rod that has a diameter of 10 mm. An applied load of some magnitude F produces a 7x10³ mm change in diameter (see figure below, original shape is blue, elongated shape is unshaded).

Question 1 You are working on a design team at a small orthopaedic firm. You have been asked to select a cobalt- chrome-molybdenum (CoCr) material that will not experience plastic deformation under a specific mechanical test, as follows... A tensile stress is applied along the long axis of a solid cylindrical rod that has a diameter of 10 mm. An applied load of some magnitude F produces a 7x10³ mm change in diameter (see figure below, original shape is blue, elongated shape is unshaded).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Table Q1 consists of 4 (four) materials with their mechanical properties. The length of a cylindrical rod 380 mm long, having a diameter of 10.0 mm, is to be subjected to a tensile load of 24,500 N. (a) Calculate the stress of the cylindrical rod. (b) Compare with data given in Table Q1 which are the likely materials for the cylindrical rod if it does not experience plastic deformation? Justify. (c) What is the likely material if the elongation is less than 0.9 materials? Justify. Table Q1 Modulus of Elasticity, Yield Strength and Tensile Strength Material Modulus of Yield Tensile Strength Strength Elasticity (GPa) (MPa) (MPa) Aluminum 70 255 420 alloy Brass alloy 100 345 420 Copper 110 250 290 Steel alloy 207 450 550
10. A standard steel specimen of 0.504" diameter elongated 0.0125" in an 8" gage length during a test where it was subjected to a tensile force of 6249 lb. If the specimen's gage length was measured to be 8.0025" after the test was over, what was the permanent plastic deformation? What is the elastic deformation and what is the modulus of elasticity of that metal? r PL AE
Question 5: Based on the stress-strain diagram for a material shown here, find the followings: Yield strength (MPa = Ultimate strength (MPa) = %3D Ductility (%) = Rupture strength (MPa) =
A titanium tube with an outside diameter of 25 mm and inside diameter of 20 mm and a length of 200 mm. When an elastic uniaxial tensile force of 30 kN is applied to this tube along its length, what is the final length of that tube? (Modulus of elasticity of Titanium is 105 GPa)
1) sketch a cantilever beam subjected to a uniformly distributed beam load over its entire length and a concentrated load at its free end. State the bending stress formula with clear indication of each parameter.
Ductile materials have more impact strength compared to brittle materials. Select one: True False
A new high stiffness plastic material has a length of 19.7 inches and a thickness of 3 mm and is being considered for use as a bone fixation plate. When subjected to a tensile load of 10000 N, the material stretches to a length of 19.88 inches. Please find the width of this material, which has a modulus of 4 GPa.
= Calculate five factors from stress strain curve for polybutadiene? Strees 0.045 0.04 0.035 0.03 0.025 0.02 0.015 0.01 0.005 0 0 10 20 30 Strain 40 50 60
9. A compressive force of 15-N is applied to a flexible poly(vinyl chloride) (CAS# 9002-86-2) wire that is 5-m long and has a diameter of 3.6-mm. If the wire contracts by 0.5-mm, calculate the compressive modulus
Which one is the correct answer please? Thank you
QUESTION 7 Which governing equations are required to solve a plane elasticity problem? Boundary conditions Equilibrium condition and boundary conditions Equilibrium conditions, boundary conditions, and the compatibility equation QUESTION 8 Which of the following conditions must a structure meet to produce a state of plane strain parallel to the x-y plane? Thin-walled Uniform in z-direction Dimension in z-direction that is much smaller than x and y QUESTION 9 What is the major advantage of using the Airy stress function for plane isotropic solids? Reduces the governing equations to only the boundary conditions and compatibility equation Reduces governing equations to a single function with a single unknown QUESTION 10 Airy stress functions are applicable for solving all elasticity problems. True False
2. A tensile test is performed on a bar of Dural (an aluminium alloy) of diameter 15 mm. The bar yields under a load of 30 kN and reaches a maximum load of 46 kN. Estimate the tensile yield stress and tensile strength of Dural