A cube of side & rests on a rough floor. It is subjected to a steady horizontal pull F, exerted a distance h above the floor as shown in (Figure 1). As F isincreased, the block will either begin to slide, or begin to tip over. [Hint: Where will the normal force on the block act if it tips?]Part ADetermine the coefficient of static frictions so that the block begins to slide rather than tip.OO fls >Ο με >0 μs < 1/1/2fls <SubmitPart BDetermine the coefficient of static friction us so that the block begins to tip rather than slide.O0 μs < 1/1/201OOfls >Request AnswerSubmitSRequest Answer

Answered: Image /qna-images/answer/620d277c-7759-48cb-b6b5-48729c443fc8.jpg

A cube of side / rests on a rough floor. It is subjected to a steady horizontal pull F, exerted a distance h above the floor as shown in (Figure 1). As F is increased, the block will either begin to slide, or begin to tip over. [Hint: Where will the normal force on the block act if it tips?]

A cube of side / rests on a rough floor. It is subjected to a steady horizontal pull F, exerted a distance h above the floor as shown in (Figure 1). As F is increased, the block will either begin to slide, or begin to tip over. [Hint: Where will the normal force on the block act if it tips?]

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A 1-meter long, 20 kg uniform bar is attached to a wall by a hinge. It is held in a horizontal position by a rope that makes an angle of 50 degrees with the wall. What is the y-component of tension in the rope (FT)? Answer in Newtons.
A man holds a 186-N ball in his hand, with the forearm horizontal (see the figure). He can support the ball in this position because of the flexor muscle force M, which is applied perpendicular to the forearm. The forearm weighs 21.6 N and has a center of gravity as indicated. Find (a) the magnitude of M and the (b) magnitude and (c) direction (as a positive angle counterclockwise from horizontal) of the force applied by the upper arm bone to the forearm at the elbow joint. (a) Number (b) Number i (c) Number i Upper arm bone- Elbow joint 0.0510 m+ Units Units Units Flexor muscle M -0.0890 m -0.330 m-
A uniform rod AB of weight 500 N and length 4.0 m is supported at two points P and Q as shown below. AP = QB = 0.80 m. A man of weight 800 N is walking from Q to B. Find the maximum %3D %3D distance x from Q the man can walk before the rod topples about Q. P Q A 1 -| × |- O 0.4 m O 0.8 m O 0.75 m O 0.6 m
Hi I needed help with this question. As shown in the figure below, a uniform beam is supported by a cable at one end and the force of friction at the other end. The cable makes an angle of ? = 30°, the length of the beam is L = 2.00 m, the coefficient of static friction between the wall and the beam is ?s = 0.600 and the weight of the beam is represented by w. Determine the minimum distance x from point A at which an additional weight 2w (twice the weight of the rod) can be hung without causing the rod to slip at point A. X=?
A 45.5‑kg box with the dimensions a×b (the width a = 0.6 m and height b = 1.3 m) is standing on a rough horizontal floor (μs = 1.3). A Professor wants to tip the box over, she pushes on the right side of the box with a horizontal force F = 140 N at a distance h = 1.04 m above the floor as shown in the picture below. The other forces acting on the box are the gravity force (applied to the CoM of the box), the static friction force Fs and the normal force N (both applied to the lower right corner of the box, point Q). Calculate the magnitude and direction of the torques produced by the forces acting on the box relative to the lower right corner (point Q). Assume uniform mass distribution. 1. The torque due to the external force, τQ(due to F) = 2. The torque due to the weight of the box, τQ(due to mg) = 3. The torque due to the friction force, τQ(due to Fs) = 4. The torque due to the normal force, τQ(due to N) =
Please help me
A 30 kg basketball goal is supported by a uniform 10.0 kg pivoting arm that is 0.70 m long. The goal and arm are raised and lowered by a cable that attaches at a point 0.50 m from the wall, as shown. When the goal is down, the cable makes a 45° angle with the arm. What is the tension in the cable?
A 1 490-kg automobile has a wheel base (the distance between the axles) of 2.70 m. The automobile's center of mass is on the centerline at a point 1.05 m behind the front axle. Find the force exerted by the ground on each wheel. each front wheel _______kN each rear wheel _______kN
The forearm shown below is positioned at an angle with respect to the upper arm, and a 5.6 kg mass is held in the hand. The total mass of the forearm and hand is 2.1 kg, and their center of mass is 16.1 cm from the elbow. (Assume the biceps muscle exerts a force on the forearm that acts vertically.) 5.6 kg B 37.5 cm 4.0 cm (a) What is the magnitude of the force (in N) that the biceps muscle exerts on the forearm for 0-60%7 N (b) What is the magnitude of the force on the elbow joint (in N) for the same angle? N (c) How do these forces depend on the angle 07 The force that the biceps muscle exerts increases and the force on the elbow joint decreases as increases. They both decrease as @ increases. They both increase as increases. They do not depend on 0. The force that the biceps muscle exerts decreases and the force on the elbow joint increases as increases.
A uniform 4.0-m plank weighing 200.0 N rests against the corner of a wall, as shown below. There is no friction at the point where the plank meets the corner. (a) Find the forces that the corner and the floor exert on the plank. (b) What is the minimum coefficient of static friction between the floor and the plank to prevent the plank from slipping?
A rough uniform rod, of length 2a, is placed on a rough table at right angles to its edge; if its centre of gravity be initially at a distanc: b beyond the edge, show that the rod will begin to slide when it has turned through an Lg² angle tan-1. where y is the coefficient of friction. +94