A compression helical spring has 12 active coils, maximum allowable deflection of 35 mm, allowable shear stress of 175 MPa, modulus of rigidity 79GPa, and is loaded with 20 Newton load. Determine the minimum wire diameter that can avoid both deflection and stress failure.

Q: Calculate the magnitude of the resultant vector given the diagram below and the following table of…

A: Fx=Fcosθ-F2cosθ2+F3cosθ3Fy=F1sinθ1+F2sinθ2-F3sinθ3ResultantFR=Fxi+Fyj

Q: Oil (sg=0.87) flows from A to E as shown. The head loss is assumed to be as follows: A to B = 0.45…

A: head losses from A to E = 0.45 V2B2g + 8.75 V2182g + 0.12 V2182g + 9 V2B2g Solving we get ; HL =…

Q: Determine the vertical reaction at B for the beam shown.

A:

Q: Determine the force in each member of the truss use the method of joints. Given: P1=10 kN, P2-20 kN,…

A:

Q: Aggregates from three sources having the properties shown in the table below where blended at a…

A: We have to determine the properties of aggregate blend for the data given in the problem. Below I…

Q: Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced…

A: Given, Sieve analysis data

Q: 3. (1) Define critical path, ES, EF, LS, LF, dummy activity and slack. (2) Cables By Us is bringing…

A: ES: It is the earliest time at which the activity can start given that its precedent activity must…

Q: Determine the value of F₁ in the figure if the resultant force is zero. F2 = 29N F3 = 40N FA 1. F₁…

A: F2 = 29 NF3 = 40 N

Q: With the given data, solve for the infiltration rate and cumulative infiltration after 1.5hrs on a…

A: Data given t=1.5 hr θr = 0.3 θ0 = 0.33675 Solution By Green -Ampt equation, Effective porosity, θe=…

Q: Hollow shaft AB (4" outside diameter, 3.5" inside diameter) is made of aluminum (E=10x106 psi,…

A:

Q: 27 Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit…

A:

Q: 8.) THREE FORLES ACT AT THE SAME POINT K SHOWN. DETERMINE THE MAGNITUDE LIl OF THE RESULTANT.…

A:

Q: Problem 4 Determine the forces in the members indicated by x. 100 k

A: Since the given loading is symmetrical the reaction at the support will be half of the total load…

Q: Facts: Don Ramon a client, hire Engineer A to design a particular project. Engr. A then develops…

A: Engineer A's design became too big and complicated for the project to complete in this scenario.

Q: Determining the locations of points and orientation of lines frequently depends on the observation…

A: Determining the locations of points and orientation of lines frequently depends on the observation…

Q: Hi I am confused on how to do this problem. I would really appreciate the help.

A: Hello, thanks for the question. Since we only answer one question, we’ll answer the first one.…

Q: Determine the horizontal and vertical displacement of joint C of the truss. The cross-sectional area…

A: E = 150 GPa = 150 × 103 N/mm2  A = 200 mm2  Determine the horizontal and vertical displacement of…

Q: 6. Determine the force in BE of the truss shown. Indicate whether the member is in tension or…

A:

Q: A 4.13-ft-diameter log (sg. = 0.82) divides two shallow water as shown in the figure. Compute the…

A:

Q: In a ready-mix plant, cylindrical samples are prepared and tested periodically to detect an

A:

Q: Determine the maximum weight W that can be supported as shown. Cable FG has a maximum strength of…

A:

Q: 2.1A cantilever beam spans 8 m and carries a uniformly distributed load as shown in Figure 2. Draw…

A:

Q: Question 4 Listen This person is responsible for determining if there are any hazardous substances…

A: This person is responsible for determining if there are any hazardous substances present before work…

Q: Question 4 A- Determine cohesive soil density in place, when; Core cutter diameter is 9.8 cm Core…

A: SOLUTION 1. given data :- diameter of core cutter =9.8cm hight of core cutter=12cm weight of soil in…

Q: At a given instant the jet plane has speed of 400 fps and an acceleration of 70 fps? acting in the…

A: Given speed =400 fps acceleration = 70 fps2 θ =600 Rate of increase in plane speed =? The radius of…

Q: he shaft is rigidly attached to the wall and made of class 25 cast iron .Sut= 25000 psi and…

A: The force of shear is a sensitive force on the surface. It's said to be the bending moment the…

Q: Question 48 schedule is a schedule in which the resources for a project are assigned to activities…

A: Resource loaded

Q: 2. A 3.0 x 1.5m sign is supported by a hollow circular column, which has a 100mm outside diameter…

A:

Q: I will rate, thanks!

A: SOLUTION 1- From curve we get maximum dry DENSITY=18.39 KN/m3  , optimum moisture…

Q: The pH of the Ocean is increasing.

A: pH increases when the basicity of the liquid increases. But due to the continuous absorption of CO2…

Q: I will rate, thanks

A: At the centerline of the clay layer, the calculations are as follows:(f) The total vertical stress…

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land.  Zoning is done or can be understood with the help of a site plan.