Calculate the magnitude of the resultant vector given the diagram below and the following table of given values. Round your answer to 1 decimal place

Q: Given the balanced Azimuths for the 4 sided traverse below, calculate the new internal angles.…

A:

Q: If a worker falls and breaks his arm on a job- site, it would be considered an occupational

A: When a worker breaks his arm at workplace this does not cause any death then this is treated as…

Q: A person working on their own home would be covered by the Occupational Health and Safety Act. O…

A: ● Solution:- False There are some rules and regulations given by OSHA that are applies to every…

Q: The Ontario Building Code outlines minimum standards for safety in new or renovated buildings. O…

A: Ans: True

Q: For a vector, F = 248.95 kN at an angle of 12.07 degrees made with the horizontal in Q3. Find the…

A:

Q: Unadjusted Preliminary Station Azimuths/ Bearings Length Departure Latitude 075 33' 01" 125.744…

A: Column no.     1     2        3        4          5          6        7        8 Station  Azimuth…

Q: Azimuths are horizontal angles observed clockwise from any reference meridian. True False

A: Azimuths are horizontal angles measured in clockwise direction from any reference meridian.…

Q: When preparing an accident report, what classification of Cause Analysis would you consider “how…

A: Whenever addressing work-related accidents, one could determine the extent of the problem by…

Q: A confined space. A trench can't be classified as a O True False

A: The confined space are those which have limited and restricted means of exit and entry. For…

Q: F= 750 N 'F2 |35°

A: solution  given that  resultant force is directed horizontally means we can conclude that  the sum…

Q: Three basic requirements determine an angle: (1) reference or starting line, (2) direction of…

A: Three basic requirements determine an angle: (1) reference or starting line, (2) direction of…

Q: The forces, which meet at one point and their lines of action also lie on the same plane, are known…

A: The force which meet at one point and their line of action line on same plane are known as Coplanar…

Q: A traverse is a series of consecutive lines whose ends have been marked in the field, and whose…

A: A traverse is a series of consecutive lines whose ends have been marked in the field, and whose…

Q: A person who undertakes a construction project for the owner of a site or building is known as a: O…

A: Worker - The person who is working for the employer at some cost at daily or monthly basis.…

Q: Determining the locations of points and orientation of lines frequently depends on the observation…

A: Determining the locations of points and orientation of lines frequently depends on the observation…

Q: Calculate the resultant force vector using the table and diagram below. Round your answers to 1…

A:

Q: Given the following for a triangle. Calculate the value(s) for a to 2 decimal places. Do not add…

A:

Q: Occupational Health & Safety is the anticipation, recognition, evaluation and control of hazards in…

A: solution  True  the main aim of this act is to reduce and control  the hazards that occur  in work…

Q: For 0° < 0 < 360° , find the angles that satisfy the equation cos(0) = -0.2091

A: cos(102.07) = -0.2091 cos(77.93) = 0.2091 cos (257.93) = -0.2091 cos(282.07) = 0.2091

Q: There are 3 ways to protect against trenching hazards. Which one of the following is not a method? O…

A: Trenching is technique of excavtion in ground . The depth of excavation is deeper than its width .…

Q: Determine the moment of the 3.6 kN force about point A? (Round your answer to the nearest tenth and…

A: M=Force ×Perpendicular distanceMoment of 3.6kN about A is

Q: Given the following for a triangle. Calculate the value(s) for C to 1 decimal place. Do not include…

A: We can find this by using cosine rule... Cosine is negative in 2nd and 3rd quadrant .

Q: A health and safety policy is written by a committee of workers and signed by the worker committee…

A: solution  A health and safety policy is a document that has a outlines of the organization committee…

Q: Question 4 Listen This person is responsible for determining if there are any hazardous substances…

A: This person is responsible for determining if there are any hazardous substances present before work…

Q: Suitable work according to WSIB for a “safe and early return to work program" should:

A: solution  The WSIB stands for work safety and insurance board

Q: The Workplace Safety and Insurance Board is controlled by:

A: solution  The workplace safety and insurance board plays a important role in province occupational…

Q: Calculate the resultant force vector using the table and diagram below. Round your answers to 1…

A:

Q: For a vector, F = 105.22 kN at an angle of 77.89 degrees made with the horizontal in Q4. Find the…

A:

Q: For <0< 360° , find the angles that satisfy the equation cos(0) 0.1111 Round to 2 decimal places. a)…

A: given :- cos(theta) =0.1111