A composite bar consists of aluminum and steel is held by rigid supports as shown. At 57°C, an axial load of 220 kN is applied to the assembly. Determine the stresses in each of the component when the temperature is raised to 1120C. Based on laboratory results for steel, E = 210 GN/m², a = 24x10-6/ºC, and for aluminum, E = 70 GN/m², a = 11.8x10- 6/0C. STEEL Ø = 15cm? ALUMINUM Ø= 1Ocm² 220 kN -100 mm 150 mm

A composite bar consists of aluminum and steel is held by rigid supports as shown. At 57°C, an axial load of 220 kN is applied to the assembly. Determine the stresses in each of the component when the temperature is raised to 1120C. Based on laboratory results for steel, E = 210 GN/m², a = 24x10-6/ºC, and for aluminum, E = 70 GN/m², a = 11.8x10- 6/0C. STEEL Ø = 15cm? ALUMINUM Ø= 1Ocm² 220 kN -100 mm 150 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam of the cross section shown is made of a steel that is assumed to be elastoplastic with E=29×106psi and σY= 42 ksi. A bending couple is applied to the beam about the z axis, causing plasticzones 2 in. thick to develop at the top and bottom of the beam. After the couple has been removed, determine (a) the residual stress at y=2 in., (b) the points where the residual stress is zero, (c) the radius of curvature corresponding to the permanent deformation of the beam.
A composite sample of carbon reinforced epoxy has dimensions of in 20 in x 20 in x 0.135 in and mass of 3 lb. The carbon fibres have a modulus of elasticity of 80(106) lb/in2 and a density of 0.15 lb/in3. The epoxy matrix has modulus of elasticity of 0.90(106) lb/in2 and a density of 0.05 lb/in3. Assume there are no voids in the sample, calculate the volume fraction of: (i) The carbon fibres (ii) The epoxy matrix in the sample.
A composite bar is made of Steel & Aluminium strips each having 3 cm² area of cross-section. The composite bar is subjected to an axial load of 12000 N. If Esteel = 3EÃ¡, the stress in steel is
The composite shaft shown consists of a solid brass segment (1) and a solid aluminum segment (2) that are connected at flange B and securely attached to rigid walls at A and C. Brass segment (1) has a diameter of 18 mm, a length of L₁ 235 mm, and a shear modulus of 39 GPa. Aluminum segment (2) has a diameter of 24 mm, a length of L₂ = 165 mm, and a shear modulus of 28 GPa. If a concentrated torque of 270 N-m is applied to flange B, determine (a) the maximum shear stress magnitudes in segments (1) and (2). (b) the rotation angle of flange B relative to support A. N 235 mm (1) B 165 mm Partial Ans: Max shear stress in Member 1 is 55.7 MPa 270 N-m (2)
= 12 mm. The The following figure depicts an aluminum I beam of height h = 0.25 m, width b = 0.2 m, flange thickness ta = 16 mm, and web thickness tw beam is reinforced by two layers of unidirectional composite material of thickness to = 5 mm. The section is subjected to an axial force N₁ = 500 kN. The Young's moduli for the aluminum and unidirectional composite are Ea 73 GPa and Ec 140 GPa, respectively. = (a) Compute the axial stiffness for this structure. (b) Compute the maximum axial stress in both the aluminum and composite layers. CS Scanned with CamScanner 1₁ I h t₂ I b po
3 For a composite bar as shown below, what is the relation between axial deformation and thermal deformations in the bar? Cu tube (1) Steel bar (2) D d- Where, o,, o, = stresses in Cu and steel bar respectively. Coefficient of thermal expansion for Cu and steel bar respectively.
A composite beam made of steel and bronze has the cross section shown. The cross-sectional dimensions are b1 = 0.5 in, b2 = 1.5 in., and d = 1.0 in. The elastic modulus of the steel is E1 = 30,000 ksi, and its allowable bending stress is 24 ksi. The elastic modulus of the bronze is E, = 15,000 ksi, and its allowable bending stress is 16 ksi. Calculate the magnitude of the allowable bending moment that can be applied about the z centroidal axis. y Bronze (2) Steel (1) bị b2 Answer: M = i Ib-in. Save for Later Attempts: 0 of 1 used Submit Answer
Show your solution with free body diagram
A sheet of aluminum is stretched in the xy-plane. If the strains in the sheet are ϵx = 0.3 x10-3 and ϵy = 0.25 x10-3, compute σx and σy. Use E = 110 GPa and v = 0.35.
The composite bar shown is firmly attached to unyielding supports. An axial load P = 207 kN is applied at 26 ° C. Find the stress in each material at 63 °C. Assume a = 11.7 µm/(m-°C) for steel and 23 um/(m-C) for aluminum. Given: Ea = 75 GPa, Aa = 991 mm², La = 204 mm, Es = 213 GPa, As = 1,213 mm2, Ls = 318 mm. Answer must be in MPa. Aluminum Steel La Ls