Answered: 1400 1200 1000 800 Fibers 600 Composite…

Engineering

Civil Engineering

1400 1200 1000 800 Fibers 600 Composite 400 200 Matrix 0.002 0.004 0.006 Strain (m/m) FIGURE P11.25 Stress (MPa)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

O 9:r. Q.2.jpg → Q.2. For the composite bar shown in Fig. 2, find the total deformation in x and y directions due to the applied load and change in temperature (drop) of 80°C, knowing that (Es 208 kN/mm?, E = 75 kN/mm?, a, = 11.7*106 mm/mm.°C, a A = 23*106 mm/mm.°C, µ,=0.29 and H=0.25. D=200 mm Steel Aluminum 150 kN 150 kN 1.5m 1.5 m Fig. 2 II
Two composite bars have the following composition. At an initial temperature of 5 degree C, there is an existing gap of 5mm. Bar 1 and 2 have coefficients of thermal expansion of a1 = 140 X106/°C and a2 = 67 X106/°C, respectively. Determine the temperature at which the 5mm gap is closed. GAP (1) (2) | B C A 540 mm 360 mm 75.20 degrees celsius 55.14 degrees celsius 95.25 degrees celsius 25.06 degrees celsius 50.11 degrees celsius O 5.02 degrees celsius 32.66 degrees celsius
The composite bar shown is fixed at the ends and is subjected to the axial load P shown. If the aluminum is stressed to 10 ksi, find the force P and the stress in the steel. 10in. 15in. Aluminum Steel A=1.5 in? E=10x10°psi A=2.0 in? 6 E=30x10°psi 6
The composite bar is initially stress-free. Calculate the stress in each material and indicate tension or compression if the temperature has increased to 25°C. Consider that the walls are unyielding and suitably braced to prevent buckling. Use 2 decimal places.
For the composite area shown in Figure 4.1f, determine the y-coordinate of its centroid. Given r1 = 75 mm and r2 = 60 mm. and h = 100 mm. The positive x and y axes of the coordination system are shown in the figure. y h
find the moment of inertia of the composite area shown in the figure below. For the X- Y centroidal axes.
3.* Figure 3 shows a tapered glued joint between two pieces of wood subjected to a tensile force. If the glue can sustain a maximum average tensile stress of 30 MPa and/or a maximum average shear stress of 50 MPa, what is the maximum angle that will permit the joint to transmit a tensile force F = 25 kN with a safety factor of 3.0? [Ans: 23⁰] F 1.6 A 3.4 Ө all dimensions in cm F
The stress-strain diagram for polyester resin is shown in the figure. Both strut AB and column CD, madefrom this material, support the rigid beam AC. Calculate the angle of tilt of the beam when it is subjectedto load P = 60 kN. The diameter of the strut is 50 mm and the diameter of the column is 80 mm.Answer: θ = 0.327 degreesPlease indicate the location of the angle of tilt in the FBD.
The composite bar in the figure is stress-free before the axial loads P1 and P2 are applied. Assuming that the walls are rigid, calculate the stress in each material if P1 = 150 kN and P2 = 90 kN.
please solve it quickly, thanks ❤️
A uniform concrete slab is to be attached to two rods whose lowers ends are initially at the same level. What is the required area, in mm², of aluminum rod so that slab will remain level after it is attached to the rods? 4 m Aluminum E = 72 GPa Steel A= 96 mm < E = 200 GPa 4 m 3 m- 0.50 m
A composite bar consists of aluminum and steel is held by rigid supports as shown. At 57°C, an axial load of 220 kN is applied to the assembly. Determine the stresses in each of the component when the temperature is raised to 112°C. Based on laboratory results for steel, E = 210 GN/m?, a = 24x106/C, and for aluminum, E = 70 GN/m?, a = 11.8x10- 6/°C. STEEL Ø = 15cm? ALUMINUM Ø= 1Ocm? 220 kN -100 mm 150 mm Activa Go to S