A clutch Is required for transmission of power between an electrical motor and a hoist required to lift 500 kg load at a top of 5 story building each store is 4 meter high in one minute The engine may run at 1500 rpm. The clutch material may be a moulded material. Determine the radial dimensions and the required actuating force.

A clutch Is required for transmission of power between an electrical motor and a hoist required to lift 500 kg load at a top of 5 story building each store is 4 meter high in one minute The engine may run at 1500 rpm. The clutch material may be a moulded material. Determine the radial dimensions and the required actuating force.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.36P: The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find...

See similar textbooks

Similar questions

2. A square threaded screw of mean diameter 25 mm and pitch of thread 6 mm is utilised to lift a weight of 10 kN by a horizontal force applied at the circumference of the screw. Find the magnitude of the [Ans. 966 N] force if the coefficient of friction between the nut and screw is 0.02. A bolt with a squore threaded screw has mean diameter of 25 mm and a nitch of 23 mm It carries an
ösalg äbäi Force appear due to spring -5 .. or string is .. Friction O Tension O Weight
A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250 mm and the inner diameter is 150 mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75 kW at 500 r.p.m. Assume uniform wear and coefficient of friction as 0.3.
A multiplate clutch has three pairs of contact surfaces. The outer and inner radii of the contact surfaces are 100 mm and 50 mm respectively. The maximum axial spring force is limited to 1 kN. If the coefficient of friction is 0.35 and assuming uniform wear, find the power transmitted by the clutch at 1500 r.p.m.
pls explain to me step by step and pls dont skip any steps i will rate your answer immediately thanks
Q2/ A belt drive consist of two V-belts in parallel, on grooved pulleys of the size. The angle of the groove is 30°. The cross – section area of each belt is 750 and u is 0.12. The density of the belt material is 1.2 Mg/m' and the maximun stress in the material is 7 MN/m?. Answer the following questions 1- The centrifugal tension in belts is (a) increases power transmitted (b) decreases power transmitted (c) have no effect on power transmitted (d) increases power transmitted up to a certain speed and then decreases
Q2 / A belt drive consist of two V-belts in parallei, on grooved pulleys of the same size. The angle of the groove is 30". The cross - section area of each belt is 750 mm? and u is 0.12. The density of the belt material is 1.2 Mg/m' and the maximum safe stress in the material is 7 MN/m. Answer the following questions 1- The centrifugal tension in belts is . . (a) increases power transmitted (b) decreases power transmitted (e) have no effect on power transmitted (d) increases power transmitted up to a certain speed and then decreases
A car engine has its rated output of 120 kW. The maxdmum torque developed is 110 Nm, The clutch used is of single plate type having two active surfaces. Axia! pressure is not to exceed 0.85 bar. External diamater of friction plate is 1.25 times the internal diameter. Determine the dimensions of friction plate and axial force exerted by the spring. Assume uniform wear and coefficient of friction to be 0.3.
Example: An automotive single-plate clutch ,with two of friction Surfaces, transmits a 300 N-mto- pairs rque at 1500 rip.m. The inner and outer diameters of the friction disck are 170 and 270 mm The cofficient of friction is o.35. The normat for- ce on the frichion Surfaces is exerted by nine helical Compre ssion springs, so that the clutch is a lways engia- ged. The clutch is dis engaged when the external force Further Compresses the (5) and the number of active Coile are (6). The Springs are madeof patented and cold -drawn steel wires of minimum tensile Strength (MTS) (N/mm²) as respectively. springs. The spring Lindex is Wire dia. 1 d(mm) 1.21.4 1.6 1.8 2 2.5 3 3.6 44.55 67 IMIm?1900 |1360|182|1480175011구20116401157이 1510|1480|144011390132011260 MTS permissible shear stress for the of the ultimate tensile strength, and (G-81370 Nlmné). Design the springs and specily their dimensiuns. Use this relation to obtaine to the total normal force required to transmit the torque. F Dis outer…
Question 4 Squared & ground end A multi disc clutch, as illustrated below, is used to connect a four-cylinder internal combustion engine to a roll mill. The lining material is made of cast iron (Permissible pressure 1.725 MN/m) and friction coefficient of 0.06 running in oil. If the outer diameter of the plates is limited to 200mm and the inner diameter to 100mm, compare the maximum amount of power that can be transferred at 2500 rpm by using the a) principle of uniform pressure and b) uniform rate of wear. (16)
4) In a single plate clutch both sides are effective. The clutch transmits 10 Kw power. The maximum torque is 120 Nm, the maximum axial force should not be more that 100 KN/m2. The outer diameter of the clutch plate is 1.3 times of the inner diameter. Find out the axial load exerted by the spring and outer and inner diameters of the clutch plate.
dynamic of machinery question photo