A closed cylindrical vessel made of steel plate 10 mm thick, with a plain ends carries fluid under a pressure of 20 N/mm², The diameter of cylinder is 400 mm and the length is 1500 mm. The steel plate young's modulus is 180000 N/mm² with a poisons ratio of .3 ,Determine the following a) The hoop stress in the cylinder wall b) The diameter change c) The change in Length

Q: The pressure of water in a pipeline was measured by means of a simple manometer containing mercury.…

A:

Q: 1.35* Design an air spring using a cylindrical container and a piston to achieve a spring constant…

A: Diameter of air spring is 4.843 inches considering length of spring equals to diameter of piston…

Q: A bar of circular cross section is to suspend a tank of water 4 ft. below a ceiling. The tank can be…

A:

Q: The minimum force P in KN should be applied to keep the gate closed, A= 9m² , I= 6.75 m is 132.3

A: Surface Area of gate, A= 9m2Moment of inertia of gate, I = 6.75 m4γ= 9800 N/m3

Q: 2. a hydraulic lift has a 0.1 m radius input piston and a 0.4 m radius output piston. if you apply,…

A: Given data: Ri=0.1 mRo=0.4 mFi=1525 N Need to determine the mass that the output lift.

Q: center of a square uniformly (a-6m and z=3.75m). Usin

A: The lagrange's formula is as,fx = x-x1x-x2x-x3x-x4x0-x1x0 -x2x0-x3x0-x4×yo+x-x0x-x2x-x3x-x4x1-x0x1…

Q: Q1:As shown in figure ( 1) determine the submerged depth of the concrete cylinder h),for equilibrium…

A:

Q: The pressure of water in a pipeline was measured by means of a simple manometer containing mercury.…

A:

Q: Q2) a horizontal air conditioning system as shown below consists of 90-degree elbows (K=0.3) and a…

A: When a fluid flows through a pipe some amount of energy is lost due to internal resistance. This…

Q: 2 ft 2.5 ft 1.5 t

A: Centroid, also called the center area of anybody is the point at which the whole area of the body…

Q: A cylindrical tank holding oxygen at 3,470 kPa pressure has an outside diameter of 425 mm and a wall…

A:

Q: The pressure of water in a pipeline was measured by means of a simple manometer containing mercury.…

A:

Q: A water tank, 22 ft in diameter, is made from steel plates that are ½ in. thick. The circumferential…

A:

Q: Water stands in the open-ends U-tube as shown in figure below. If the entire system is rotated about…

A:

Q: A tank contains two substance oil (A) and water (B) subject to variable air pressure; the dimension…

A:

Q: Q15: In Figure below, calculate Fx and Fv per unit width of the cylinder to 1.5 m cylinder Water 35

A: solved

Q: ssel having thickness of 0.2 m. A gas is filled inside the vessel having a pressure of 10 Mpa. How…

A:

Q: Question (1):- Find the pressure in the pipe shown in figure.if Pmer=13600kg/m' and pw=1000kg/m. 80…

A:

Q: s) A cylinder that is 750 mm in diameter and 2.5 m long has a specific weight of 835 N/m³. It eid…

A:

Q: 1.45 The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 3. A gas is under pressure of 40 bar abs at 40°c. a. Compute the pressure in kPa b. Compute the gage…

A:

Q: a) Fig. 2 shows a rim of a tractor tyre of diameter 60 cm and width 25 cm. After inspection, the…

A:

Q: Q A thick-walled cylinder has an inside diameter of 150mm. The inside of the cylinder is subjected…

A: Soln:-  d1 = 150 mm             r1= 75 mm               P1= 350 bar = 350 × 10^5 pa           Max.…

Q: A man had a high blood pressure which is about 180mm HG(SG = 13.6). A nurse is about to inject…

A: Given:  h = 180 mm SG = 13.6

Q: 8.6 m 30° hc hp F Hinge YP Water 5m Gate Ic= a/12 Figure 4 An inclined rectangular gate submerged in…

A:

Q: 1) FIND REACTIONS AT SUPPORTS A & B A fin 300 N/m 1.5m 1.5m 400 N/m 1.5m B

A:

Q: we derive the formula that gives us pressure and deepness in situations that spesific weight changes…

A:

Q: A closed circular tank filled with water and connected by a U-piezometric tube as shown in figure…

A: Given information :   Fall in water level = 3cm The principle we have to apply here is Bernoulli's…

Q: Concrete Cylinder water Delm Figure 14) QI: As shown in figure (1), determine (h), for equilibrium…

A:

Q: The pressure of water in a pipeline was measured by means of a simple manometer containing mercury.…

A:

Q: 4. Compute the pressure different between 'M' and 'N’ for the system shown in figure. -S = 0.92 M.…

A:

Q: A circular gate of radius_____ m is submerged in a liquid with its top edge flushed on the liquid…

A: Given   Radius, R = 2 m  Weight, w = 15.88 kN/m3 Height of circular gate center from its free…

Q: The cover is mounted on a water-filled reservoir as shown in the figure with a width of 2 meters…

A:

Q: 5. The gas tank (inner diameter 1.5 m) is made from steel which has a yield strength of 250 MPa. If…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.