Q1:As shown in figure ( 1) determine the submerged depth of the concrete cylinder h),for equilibrium the gate AB (The concrete cylinder weighs 19KN andthe gate AB weighs 25KN) Assume Fictionless pulley Cable gale width Im Concrete Cylinder water 品 Delm 0.45 Figure 14) Hehinge)

Q1:As shown in figure ( 1) determine the submerged depth of the concrete cylinder h),for equilibrium the gate AB (The concrete cylinder weighs 19KN andthe gate AB weighs 25KN) Assume Fictionless pulley Cable gale width Im Concrete Cylinder water 品 Delm 0.45 Figure 14) Hehinge)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylinder with a radius of r=1 m is hinged at location A. It is used as a gate to block water in the reservoir with H=6 m a) Determine the horizontal and vertical components of the resultant hydrostatic pressure force acting on the curved surface AB per unit lentgh and its direction. b) For this cylindirical gate, what is the required weight per unit length, to open automatically at H=6 m. water A
Q3: Three forces are acting on a steel plate with 4m length by 4m width shown in figure. These three forces are required to cause a horizontal resultant acting through point A. If F = 504N, 1) The value of horizontal resultant R is: E A D 853.814N + O 796.894N → O 711.512N - O 640.361N → O None of these
1. A dam as shown in Figure Q.1 is to be built to hold 256 m³ of water. The curved surface of the dam has a shape prescribed by the relation y=x. If the width of the dam is 8 m, determine: 5 m Water Level Dam h b Figure Q.1. Schematic of the proposed dam. i) the height (h) of the dam, and ii) the resultant hydrostatic pressure force acting on the curved surface. Take density of water as 1000 kg/m³
Q3: Three forces are acting on a steel plate with 4m length by 4m width shown in figure. These three forces are required to cause a horizontal resultant acting through point A. If F = 504N, 1) The value of horizontal resultant R is: F E A D B.
The bottom corner of a water tank that is 3 m wide (into the page) is constructed with a flat panel at an angle of 45° as shown in the figure below. The panel in question is shown as a heavy line. Note that water has a density of 1000 kg/m3. Determine: 2a) The magnitude of the total resultant force acting on the panel, FR 2b) The depth of below the water surface at which the resultant force vector acts on the panel, d
Gate AB in the figure below is a 5-ft wide, vertical, rectangular gate, hinged at A and restrained by a stop at B. The water depth, h = 9.5 ft. Determine: a) the hydrostatic force acting on the gate and the location of the center of pressure b) The vertical and horizontal reactions at the hinge at A.
An infinitely long cylindrical container has a cross section area of radius R, and is placed horizontally with gravity being in the −y direction, as shown in the figure. The cylinder is 50% filled with water (the shaded part), with density ρ. The other 50% of the volume in the cylinder is filled with air with constant pressure of p = p0. The length of the cylindrical container in the axial direction is W. b) Use the surface integral method to compute the hydrostatic force acted on the 4th quadrant of the cylinder wall, as shown by the thickened line in the figure.
Question ): For figure shown below, estimate: 1. The resultant hydrostatic force (FR) acting on the curve gate AB if the gate width = 1 m. 2. The direction of FR (0) 1 m Water 1m LA
As figure show are depicts the cross-section of a closed-end cylinder with an internal diameter of 0.2 m and an exterior diameter of 0.4 m with a thick-walled pressure vessel (closed-end cylinder) with an internal diameter of 0.2 m and an external diameter of 0.4 m. Both internal and external pressures, Pi and P, are applied to the pressure vessel. Find the following given P. = 10 MPa:a). The internal pressure Pi, which will result in a 150 MPa tensile hoop stress at point B, which is in the middle of the cylinder wall.b). Draw all of the stress distributions over the wall thickness and their stress values on the cylinder's inner and outer surfaces.c). The longitudinal tension that the cylinder is subjected to.
: The tank shown in figure below is partially filled with water. On the top of the water there is compressed air for which the pressure is the same at every point (h1=4m, h=0.4m a=2m, 1=10 kN/m3, 2=136 kN/m3 Determine:a) The pressure, due to the compressed air on the water surface,b) The force on the triangular gate AB,c) The point of application of the hydrostatic force on the gate from the bottom of the tank