1.45 The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thicknesses shown in the figure. The working stresses are 70 MPa for shear in the rivets and 140 MPa for bearing stress due to the rivets. How many 19-mm-diameter rivets are required to fasten the fol- lowing members to the gusset plate: (a) BC, and (b) BE?

1.45 The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thicknesses shown in the figure. The working stresses are 70 MPa for shear in the rivets and 140 MPa for bearing stress due to the rivets. How many 19-mm-diameter rivets are required to fasten the fol- lowing members to the gusset plate: (a) BC, and (b) BE?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the sheer stress in the rivet in MPa( 3 decimals)
A 3/4-in. horizontal steel bar loaded at constant tension and welded to a vertical support is shown in the figure. Determine the force F if the weld is E6013
are of 10 mm size and the weld length is 30 mm. loading F as shown in figure. Both legs of the fillets considering the minimum throat of the weld, the A fillet welded joint is subjected to transverse loading Fas shown in figure. Both legs of the fillets ere of 10 mm size and the weld length is 30 mm. If the allowable shear stress of the weld is 94 MPa, considering the minimum throat of the weld, the maximum allowable transverse load in kN is F
A steel bar of thickness h is welded to a vertical support as shown in the figure. Find the safe force Fif the maximum allowable shear stress in the welds is Tallow- 45 where b= 60 mm, c= 160 mm, d= 60 mm, h = 5 mm, and Tallow = 140 MPa. The safe force is |KN.
b) For the truss in the figure below, determine the zero-force members and give a short explanation to support your answer. B C D A H G F -1.5 m-1.5 m- 1.5 m-1.5 m- 2m 2 m
Solve it
I need handwritten otherwise skip all parts with option or I'll dislike
I am struggling with this question
A pin-jointed truss ABC shown below consists of two links AB and BC. These links are 6 mm thick and 20 mm wide as shown. There are support brackets at A and C. All pins are 12 mm in diameter and a vertical force, P = 5 kN is applied at pin B as shown. The angle 0 =40 deg. and the angle ß = 0 + 20 deg. The normal stress in link AB is (The result is accurate to one decimal place, in the unit MPa. Please write down only the value of your final result) -$12mm A B 20mm -1.0m- P B
3 - A roof truss and the detail of the riveted connection at joint B. Using allowable stresses of t = 70 MPa and ob= 140 MPa, how many 19-mm-diameter rivets are required to fasten member BC to the gusset plate? Member BE? P = 175 kN 6 m 14 mm gusset plate 4 m 4 m E 4 m 4 m P/2 P/2 75 x 75 x 13 mm 75 x 75 x 6 mm Pac
A simple pin-connected truss is loaded and supported as shown in the figure. All members of the truss are aluminum pipes that have an outside diameter of 3.00 in, and a wall thickness of 0.284 in. Determine the normal stress in each truss member. Assume P-2 kips, Q- 3 kips, a- St.b-7 ft, and h-6 ft. The stresses are positive if tensile and negative if compressive. (1) Answers: ksi ksi ksi
The cantilever truss in the figure is hinged at D and E. Find the force in member BD. 1000 1b 60° 60° 30 C 10' la00 16 C00 (6.