A closed cylindrical vessel 1.50 m in diameter and 3 m high is filled with 2.50 m of glycerin (sg=1.50). It is rotated about its own vertical axis at a constant angular speed of 175 rpm. The air space above the water is under a pressure of 115.525 kPa. Determine the height of the Paraboloid in m Determine the area of the uncovered portion in sq.m. Determine the pressure acting on the bottom of the tank along its circumference in kPa.

Q: 3. If blocks A and B of mass 10 kg and 6 kg, respectively, are placed on the inclined plane and…

A:

Q: The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m.…

A: Deformation δ=PLAEWhere,P=ForceL=LengthA=Cross sectional areaE=Modulus of elasticityUsing…

Q: A rectangular gate having width of 5 ft is located in the sloping side of a tank as shown. The gate…

A:

Q: The head produced by a liquid of relative density 1.62 is equal to the pressure of 250 kPa. What is…

A: given- relative density ρ=1.62pressure P=250 kPa=250×1000 Pa

Q: The laminar row takes place between closely spaced parallel plates as shown in figure below. The…

A: Laminar flow between parallel plates- Velocity profile u=v(y/h) Gap height h=5 mm=0.005 m, Specific…

Q: 2) Determine the reaction forces at both walls, if temperature is raised from 30°C to 90°C. The…

A:

Q: 2. The block of weight W2 is being held in its position by two cylindrical rollers resting on…

A: For maximum value of W2 block should be in equilibrium.

Q:

A:

Q: The vena contracta is the location of cross-sectional ......... diameter of .flow of liquid

A: ANSWER: SMALLEST

Q: up B What is the total resultant force (kN) that is applied on surface AB? Then find the location of…

A:

Q: Q1: Determine the range of P for which the system of two blocks will be in equilibrium. Friction is…

A:

Q: J-Find the rise in a tube capillary * shown for a water- glass interface e=0 iF the tube radius is…

A: Capillary rise in a tube formula is given in the picture

Q: ing girder level P(t) = 890 sin 5.3t (N). Assuming 5% of critical damping. Determine: (a) the steady…

A: the problem has been solved by basic of dynamics. to solve first we have to change units into mks…

Q: : Find the required force (F) to pull athin plate at the middle point between two large plates,…

A: When central middle plate will move then both upper and lower plates will resist it's motion and…

Q: Calculate the deflection ABv,. E = 10,000 ksi C 10' 4 in² A 6 in² 4 in² 10' 30 K D 6 in² 6 in² 10' B

A:

Q: A fluid is contained between parallel plates; the bottom plate is fixed and the upper plate moves.…

A:

Q: 4.In turbulent flow the particals moves in all directions and randomly mixes with each other. O true…

A: Turbulent flow is a type of fluid (gas or liquid) flow in which the fluid undergoes irregular…

Q: What is the equations for static equilibrium? * ΣFx 0 ΣFy -0 ΣFz 0 EMz = 0

A: Equations of static equilibrium - These are the equations developed, considering all the forces and…

Q: stion 24 The initial pressures at A and B are the same at 103 kPa. If the pressure at the liquid at…

A:

Q: Particle A lies on the x-y plane and is acted on by the three forces shown. Find the resultant of…

A:

Q: Qq: A liquid of (N =1-25 Pa.s.) tills the space of (Sum) shown in figure below. Calculate the forque…

A: Step 1

Q: Q34 If the surface tension of water is 0.06N/m, then the capillary rise in a tube of a diameter 1mm…

A: Surface tension T=0.06 N/m, Diameter d=1 mm, Angle = 0o Capillary rise=?

Q: Mass of crate: 100 kg μk: 0.25 Determine the maximum compression, x. k = 2 kN/m 10 m 45°

A:

Q: A film of oil exists between two horizontal plates spaced 3mm apart. The lower plate is fixed and…

A: Given Data: The spacing between the horizontal plates is T=3 mm. The lower plate is fixed and upper…

Q: m=..... kg V h=......m E=2.5×105 MPa I= 7.5×103 m㎥ A small water tank is constructed on a rigid…

A:

Q: Determine the magnitude of the component of F acting along segment BC of the pipe assembly

A: Given :

Q: 5- A solid sphere of diameter 240 mm is subjected to an external uniform pressure of 100 MPa. For E…

A:

Q: Find the capillary rise ( h) in the tube shown in the figure for a water-air-glass interface with 9=…

A:

Q: A STRAIGHT LINE IS DETERMINED TO BE 3234.25 m WHEN MEASURED WITH A 50-m STEEL TAPE SUPPORTED…

A: Measured distance (L) = 3234.25 mLength of steel tape(l) = 50 mPull during measurement (Pm) = 4.5…

Q: A 100 kg block is resting on a smooth inclined surface. Determine the value of T to maintain…

A:

Q: Qq; A liquid of (N =1.25 Pa-s.) fills the space of (Smm) shown in figure below. Calculate the forque…

A: given , vertex angle=30°=2αviscosity of oil=μ=1.25poise=.125Na/m2speed=60rpma=0.3m and b=0.7m…

Q: Block A and B are homogeneous with 20 kg and 25 Kg mass respectively. The system is subjected to the…

A: Determine whether the two block are in a static condition or moving.

Q: A 50m steel tape is used to measure the distance of the line and found to be 842.25m. During…

A: To Find the correct length of line measured with 50 m tape.

Q: 8. Determine the v-component of F1. (kN) 9. Determine the u-component of F1. (kN) 10. Determine the…

A: Component along the angle is Fcosθ

Q: A force is applied at the left end of a block resting on a surface. The internal effect of the force…

A:

Q: 60 kN 40 kN 50 kN 1.5 m 1.5 m 1.5 m 2m R2

A:

Q: Particle A lies on the x-y plane and is acted on by the three forces shown. Find the resultant of…

A: To find resultant force

Q: Plate with 0.13 m wide and 0.25 m length passes thru oil with layer 3.5 mm and 5 mm thick. Both…

A:

Q: Q34 If the surface tension of water is 0.06N/m, then the capillary rise in a tube of a diameter 1mm…

A: Surface tension of the water T=0.06 N/m,Diameter d=1 mm,Angle = 0oTo Find-The value of the capillary…

Q: A solid cone of radius ro and vertex angle 20 is to rotate at an angular velocity w. The cone is…

A: Object: Solid coneDimensions: Radius:   Vertex angle: 2θHousing: Present, with a gap between the…

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?