Particle A lies on the x-y plane and is acted on by the three forces shown. Find the resultant of the three forces. 4.5m 2.1m 1400 N 900N 1.8m 1000N

Q: 4. Find the vertical distance of the centroid from the base of the section shown. Calculate the I…

A:

Q: If a W16x40 steel column is to be protected with 5/8" Type X gypsum in a box profile, what would be…

A: Given, Steel column- W16x40 Wallboard protection-5/8 inch Type X Gypsum box Resistance,…

Q: H.W No.2: A 12 inch circular pipe is to be installed in a positive projection embankment under an…

A: For pipe installed with less than 3 feet of cover, it is sufficiently accurate to calculate the…

Q: COMPUTE MV, FOR BEAMS 1, 2, 3 AND 4. ASSUMPTIONS: LIVE LOAD = 75p56 MECHANICAL EQUIP = SopsF 10'…

A: Live load= 75 psfMechanical equipment= 50 psfExterior wall = 500 lb/ftSelf weight of beam=150…

Q: (2) 27"/ 6" TE #4 4 #9 (1) d = ? (2) C= ? 39 Jove d-c fé= 3 ksi Grade 60 steel NWC. & Mn = ? #4 tied…

A: Given: fc = 3 ksi fy = 60 ksi Cover = 1.5 inch

Q: List down installation process of tie beam

A: Tie beam is a horizontal beam laid on ground to increase the stiffness of column and hence to reduce…

Q: We are designing a small office building with exterior siding finish: What is the code requirement…

A: To Design the Small office building with exterior siding finish. The 2007  California Building Codes…

Q: Determine the moment resisting capacity (Mr) of the given cross-section -H=500 mm- 6 Φ 20 ←B=350…

A: Solution: Stress-strain profile:

Q: Determine external indeterminacy

A: Given data : Number of external support reaction (R)=3+1+2=6

Q: Define the process of computing the design factored loads ?

A: The strength of structural members of reinforced cement concrete is determined with the help of…

Q: How does the stone column installation is termed a vibroreplacement procedure?

A: Vibro- stone columns or aggregate piers are an series of crushed stone pillars mounted under a…

Q: All specific sizes recommended by CRSI below meet minimum requirements of ACI 318 Recommended End…

A: The Standard Specifications require that reinforcing steel hooks and bends conform to the provisions…

Q: Explain the minimum no of bars to be provided in circular column ?

A: The minimum number of bars in column is 6 for the circular column.

Q: Which of the following represents the effective slab width for the composite beam (Beam 1)…

A: For the beam (beam 1) highlighted in the figure, the span of the slab it needs to support is,…

Q: Problem 1-3: All stirrup information is provided, including spacing. You will find the resultant…

A:

Q: Please draw an FBD for the problem.  One for the overall structure and then one for DBA and then…

A:

Q: 5/138 Determine the weight w per unit length of the 30-ft steel beam which will produce a maximum…

A: Given:- The length of the steel beam = 30 ft The maximum tension in the cable = 1500 lb To…

Q: Define how to determine the required depth of embedment of the anchor bolts into the concrete ?

A: Anchor bolts are used to move loads through components like ledgers, sills, including supporting…

Q: concrete stair and landing reinforments: -the trend bars 3-D 10 mm -the riser bars D-10 mm @ 150…

A: In concrete stair case This is a typical stair case details

Q: pressure and suction CpCg

A: For the wind load acting on a building, in the calculation of external pressure acting statically is…

Q: he recommended steel ratio for a slab having thickness of 125 mm is 0.00215 determine the required…

A: Steel ratio is Ast/BD

Q: 4.4 Refer to the framing span diagrams from Architects' Studio Companion and answer the following…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: A typical bay of a composite floor system is illustrated in below. Select an appropriate ASTM A992…

A: Given, Length of the beam L, L=45 ft Spacing c/c s, s=10 ft Dead and live load including self weight…

Q: Fill in the blanks: Wind or earthquake loads can be in load calculations. or The failure mode of a…

A: Wind or earthquake loads can be  Horizontal or lateral in load calculations.

Q: Define The applied loads

A: Applied loads are characterized by rapid changes in magnitude, which can result in structural…

Q: (2) 3#9 12" 21" I 3" fé=3000 psi Grade 60 steel NWC. & Mn = ?

A: Given:- The steel reinforcement provided in the beam = 3 bars - #9 diameter The width of the beam is…

Q: Are the compressions found on the same location in the slinky before and after hitting the wall?

A: No, compression doesn't found in the same location in the slinky before and after hitting the wall,…

Q: Select the correct statements regarding glulam layups for flexural and compression members.…

A: When used in heavy timber construction, Glulam ensures high earthquake resistance and excellent…

Q: Find all the concrete amount in the foundation

A: Step 1: Identify the number of footings in the plan, in this case we have 12 different footings.…

Q: Roof Sheathing Panels in High Velocity Hurricane Zone (HVHZ) shall have nail spacing 4 in. o.c. at…

A: High Velocity Hurricane Zone (HVHZ) is a building code that is used to differentiate the areas hit…

Q: Locate centroid for the following composite section:

A: For the C12×25 Area=7.35in2centroid from base is 0.674inFor the C12×25 Area=20in2centroid from base…

Q: Il: DRAW THE SECTION DETAILS FOR RAIL AND SLEEPERS SECTIONAL DETAILS FLEXIBLE PAVEMENTS SEOTIONAL…

A:

Q: 4. SHOW THE FRAMING ON THE ROOF FOR THE HOUSE TO THE RIGHT. « PREFABRICATED TRUSSES POST AND BEAM…

A: Roof framing is considered the most complicated thing in the house because of the angles involved.…

Q: Define the term rakers?

A: The word "raker" is made from "rake" which refers to an angle of a slope which is measured from the…

Q: 42. How many square feet of forms are needed to construct the columns shown in Figures 5-26 and 5-…

A: Consider the footing placement as in Figure (1).

Q: Select one: O á. Panel 1 is two-way, panel 3 is two- way, panel 2 is one way Ob. Panel 3 is two-way,…

A: The slab is considered as the plane element which is classified based on the aspect ratio. The slab…

Q: Evaluate the use of hollow block  as chosen material to use in ribbed slab

A: The ribbed slab is a reinforced concrete slab in which hollow blocks are provided in the tension…

Q: draw One-way slab- 12 mm diam. main bars spaced @        300 mm o.c. b/w with 10 mm diam. extra top…

A: Solution: Given: One-way slab: Main bars = 12 mm diameter Temperature bars = 10 mm diameter

Q: What are the different dimension styles used in AutoCAD?

A: This question is related to the Autocad from Civil Engineering. In this question ask about the…

Q: Using Centroid by Composite Shapes, determine the x- and y-coordinates of the centroid of the shaded…

A:

Q: BM 1 STA BM 1 BM 1 El.- 100.00 X 4.683 HI == Benchmark El.- 100.0 IP#1 BS Existing Building TP 1…

A: Given data,Benchmark 1=100'From IP#1BS=4.683' & FS=5.812'

Q: Define the K0 Stepped-Blade Test ?

A: In situ measurements of lateral pressures in clay, sediment, as well as sandy soils are made with…

Q: Using Centroid by Composite Shapes, determine the x- and y-coordinates of the centroid of the shaded…

A:

Q: Number of modular bricks required for one cubic metre of brick masonary are

A: Brief concept introduction- Bricks- These are one the most common building materials used in the…