Question 2A clearance fit between a Shaft and a Pulley is given as 15 H8-f7 (units in mm). Please referto the Limits and Fits document from myUNISA additional resources; for convenience anexcerpt o this table is provided on Page 5.Do the following:2.1State the nominal shaft sizeUsing the ISO Limits/Fits table, determine the upper and lowertolerance for the shaft. (Hint, consider the H8 designation and makesure units are correct)2.2Using the ISO Limits/Fits table, determine the upper and lowertolerance for the hole (bearing). (Hint, consider the f7 designation andmake sure units are correct)2.3 SELECTED ISO FITS -HOLECLEARANCE FITSH11H9H9DIAGRAMTO SCALEFOR 25mmDIAMETERH8H7H7HOLES96h617e9d10SHAFTSc11Nominal Sizes ToleranceToleranceToleranceToleranceToleranceToleranceOverToH11c11H9d10H9H8 f7H7H7h6e996mm0.001mm 0.001mm 0.001mm 0.001mm 0.001mm 0.001mm 0.001mm0.001mm 0.001mm 0.001mm 0.001mm 0.001mmmm60-120+2520+25-14314+10+1039-16+7570145+303078+302030183-102812+1212801703640+38-25+22132815151014*11043+2732-75163443+1818111018205-120-17130110+52+2145-149+52to33-2041+21131830-2409220120-280160304050+39+252530+628082+2516160130180112-254050-290Figure 2

2.1 A nominal size, also known as a trade size, is a size that is only used for identification…

A clearance fit between a Shaft and a Pulley is given as 15 H8-f7 (units in mm). Please refer to the Limits and Fits document from myUNISA additional resources; for convenience an excerpt o this table is provided on Page 5. Do the following: 2.1 State the nominal shaft size Using the ISO Limits/Fits table, determine the upper and lower tolerance for the shaft. (Hint, consider the H8 designation and make sure units are correct) 2.2 Using the ISO Limits/Fits table, determine the upper and lower 2.3 tolerance for the hole (bearing). (Hint, consider the f7 designation and make sure units are correct)

A clearance fit between a Shaft and a Pulley is given as 15 H8-f7 (units in mm). Please refer to the Limits and Fits document from myUNISA additional resources; for convenience an excerpt o this table is provided on Page 5. Do the following: 2.1 State the nominal shaft size Using the ISO Limits/Fits table, determine the upper and lower tolerance for the shaft. (Hint, consider the H8 designation and make sure units are correct) 2.2 Using the ISO Limits/Fits table, determine the upper and lower 2.3 tolerance for the hole (bearing). (Hint, consider the f7 designation and make sure units are correct)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 1 A suitable factor of safety to apply when selecting the cable for a factory hoist is: 05 O1.2 0.2 O 25 QUESTION 2 A winch drum of diameter 199mm turning at 14rpm lifts a load of 5.5kN. What is the winch output power? Give your answer in W to 1 decimal place without units eg 102.3 NOT 102345239 W QUESTION 3 The figure below shows two proposed designs of drums to solve the same load and line speed lifting arrangement. What is the biggest advantage with design A: A The torque on the drum shaft will be lower O The rope speed will be lower The bending moment in the drum shaft will be lower O The weight of the drum material will be less 刚 B
Apply a perpendicularity tolerance to control the pin within a 0.015" cylindrical tolerance zone at MMC relative to datum surface. Pin length is 1.000", base diameter is 2.000". Finish the print. +.002 -.001 te -0.375 Datum Feature
I need help solving problem numbers 4--15.
Which method specifies the tolerance by providing dimensions for the upper and lower limit in place of the dimension? a. general tolerance b. angular tolerance c. single-unit dimensioning d. plus-minus dimensioning e. limit dimensioning
Chapter 3: 13. What type of geometric tolerance has no datum features? 14. A theoretically exact dimension is called a 15. The feature symbol specifies that a group of two or more interrupted features of size are to be considered one single feature of size. 16. For an individual regular feature of size, no element of the feature shall extend beyond the maximum material condition boundary (envelope) of perfect form. This statement is the essence of 17. What is the name of the symbol used to identify physical features of a part as a datum feature and must not be applied to centerlines, center planes, or axes? 18. The is the condition in which a feature of size contains the maximum amount of material within the stated limits of size. 19. The total positional tolerance equals the sum of the tolerance and the tolerance.
7. This problem relates to tolerance stack-up using the absolute tolerance system, as explained in section 1-14. In the figure below, specified dimensions are as follows (all units in inches): a d 1.750 + 0.001 2.000 + 0.003 3.200 + 0.005 ?+0.010
4- 100 ft tape was used to measure line DF; if the correct tape length is 100.05 ft, the field temperature is 37°, the standard temperature is 20°, the thermal expansion coefficient is 0.00004, Calculate the corrected distance if the measured one is 425.50 ft.
A rectangular block 100 mm x 150 mm has a hole with diameter 60 mm at the center. The hole tolerance zone is H7. The thickness of the block is 45 mm. The tolerance zone for the hole is: O 0/+30 um O -19/0 um O +10/+40 um O 0/+25 um
I need help matching the terms to the phrase it describes.
I need help answering this quick review pertaining to the print provided.
Correct answer writing
state the functions of interference fit and draw it on illustration of size tolerance zone .