A circular RCC water tank has an internal diameter of 10 m and has maximum height of water as 4 m. The thickness of wall is 160 mm and the walls of the tank are restrained at the base. IS-code coefficients for moment in cylindrical wall fixed to the base is given below. 2 Coefficient at point DT 0.8H 0.9H 1.0H 10 +0.0028 -0.0012 -0.0122 12 +0.0026 -0.0005 -0.0104 14 +0.0022 -0.0001 -0.0090 Take unit weight of water as 9810 N/m³ where, H = Height of tank, D = Diameter of tank, T Then moment at the base of wall using the given table is = Thickness of wall

A circular RCC water tank has an internal diameter of 10 m and has maximum height of water as 4 m. The thickness of wall is 160 mm and the walls of the tank are restrained at the base. IS-code coefficients for moment in cylindrical wall fixed to the base is given below. 2 Coefficient at point DT 0.8H 0.9H 1.0H 10 +0.0028 -0.0012 -0.0122 12 +0.0026 -0.0005 -0.0104 14 +0.0022 -0.0001 -0.0090 Take unit weight of water as 9810 N/m³ where, H = Height of tank, D = Diameter of tank, T Then moment at the base of wall using the given table is = Thickness of wall

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 2: A one-story shear building with an appendage attached to its top is subject to a horizontal ground motion y;(t), as shown in Figure Q2. The girder of the building is assumed to be rigid and the columns are assumed to be massless. The appendage is modelled as a lumped mass system of one degree of freedom. The structural damping is neglected. El = 600 x 10°N - m², Elz = 400 x 10°N - m² (a) Derive the equation of motion for the system in terms of the absolute displacement as well as the relative displacements u = y1 – Ya and uz = y2 - Ys- m2 = 5000kg El. m, = 20000kg El. El y-(t) Figure Q2
3
Need asap pls.
Consider the simply-supported overhang beam shown. There is a pin support at A, a roller support at D, and an overhang of 2m. Calculate the support reaction at D. 5kN/m 2kN/m B 3m 2m- 1m 2m 2m
For the quarter circle gate BC with a hinge at C, the force P = .. kN to hold the gate stationary for 5.5 m wide gate. Let r = 4.5 m В | Ir m Water C Answer: Answer
A 200-mm-diameter pulley is prevented from rotating relative to 60-mm-diameter shaft by a 70-mm-long key, as shown. If a torque T = 2.2 kN-m is applied to the shaft, determine the width b if the allowable shearing stress in the key is 80 MPa. 70 mm Shaft 200 mm-ø Shaft 60 mm-ø O 13.09 mm O 17.46 mm O 15.43 mm O 18.34 mm
Determine the support reaction at A B 500 N 2 m 45 2 m Select one: a. 600 and 400 b. 300 and 700 c. 500 and 500 d. 400 and 600
A hole is punched at A in a plastic sheet by applying a 540-N force P to end D of lever CD, which is rigidly attached to the solid cylindrical shaft BC. Design specifications require that the displacement of D should not exceed 15 mm from the time the punch first touches the plastic sheet to the time it actually penetrates it. Determine the required diameter of shaft BC if the shaft is made of a steel with G = 77.2 GPa and Tall = 80 MPa. D 500 mm 300 mm The required diameter of shaft BC is mm.
A beam is supported by a pin at point A and a roller at point B. The beam has a length L = 8 m and a distributed load w = 458 N/m. Determine the magnitude in (N) of vertical reaction at point B. THEM L Telll *
Note: change 6 meters arc This is number 6, fluid mechanics
Use double integration method
Determine the internal forces at point D. Member AB has a unit weight of 500 N/m; member BC has a unit weight of 800 N/m В 22.5° C To0 mm 30 A D 700 mm