• Find: External reactions in x and y directions needed to hold fixed vane. F,+ • Solution: OTS = 0.90). 30 V-28 m Q-0.20 m'/s V,-27 m/s

Q: Q/Deduce the ISO from the projections 60 80 30 40 R30

A:

Q: Q1. Figure shows a cross section view of a structure. All dimensions are in mm. (a). Determine the…

A: Solution: Given:

Q: How many "varas" are there in a single ruler measurement?

A: A single ruler is the standard ruler which has measurements given in inches or mm. It is used to…

Q: Q4: Find the total area A of the shape below in Figure 3?

A: Given data- A semi-circle of radius 'r' as shown- To Find- The total area of the shape.

Q: Do not include the unit in writing the answer. Use small letters (lowercase) in writing the words.…

A:

Q: Determine the vertical distance H from the lower edge of the cross-section to the y coordinate of…

A: Given figure,

Q: What is area of plot in square shaped. Length =20feet.

A: This question is related to Building Planning and Design from Civil Engineering. In this problem we…

Q: Find the area of a rectangle with a length of 6 inches (in) and a width of 2 inches.

A: Solution:- A rectangle is a two dimensional shape or polygon with four sides, four vertices, and…

Q: 0 mm 20 mm x= ky? 30 mm etermine: enter of Area in x direction, overline x 1U-Sclect) mm enter of…

A: To find centroid

Q: An isometric drawing contains a cube stacked directly on top of another cube. What is the surface…

A: One cubic has six square surface and another club has same, if both are in come in contact with…

Q: Calculate the dimension marked in red X in the following figure

A: for the given structure shown  22×26  unit2 - dimensions of the upper block40 unit - length of the…

Q: You are a professor of architecture. Show your students where the horizon line and vanishing points…

A:

Q: From the diagram shown, all dimensions are in millimeters. Find the length of side x. 89 00' 2,268…

A:

Q: 23mm R2 166.5mm 28° 34° 235mm 175mm 250mm R1 R3 125mm

A:

Q: Conver the ratio scale 1:2400 to an equivalence scale. O 1 inch = 20 feet O 1 inch = 2,400 feet 1…

A: Given data, RF of a scale = 1:2400 I.e 1 inch = 2400 inch

Q: Convert the equivalence scale 1 inch = 30 feet to a ratio scale.

A: Solution:- Scale:- The scale of the map is the ratio of a distance on the map to the corresponding…

Q: Determine the shape factor

A: Given:- An I- section is given  To determine:-  The shape factor of the given section

Q: What of the following about the scale is/are false ?

A: The scale represents the ratio between the measurement drawn in a plan to the actual measurements.

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 5)…

A:

Q: Do not include the unit in writing the answer. Use small letters (lowercase) in writing Complete the…

A:

Q: What is area of plot in rectangle shape. Length =20feet, breadth=10 feet.

A: Finding area of rectangular plot Given: length= 20ft Breadth=10ft

Q: me miller indices.

A: Given figure

Q: Complete the table below. LINE BEARING DIST (M) AB N 68° 11.9' E 53.852 BC S 45° 0' E 28.284 CD S…

A: Answer  Let us first calculate the latitude and departure of given lines To calculate the Latitude…

Q: multiply the numbers. 662*706

A: GIVEN QUESTION 662 X 706

Q: where did you get the 3.6 that you divided in v?

A:

Q: Question 3/ List the steps in details to draw the shape below using AutoCAD .commands -8.0000 0.5000…

A: To Determine Th Steps and the Commands used in AutoCAD to draw the given figure.

Q: express each common fraction as a decimal fraction. 8⁄25

A: Given data:- The given fraction is, 825

Q: Rotate the objects shown below by the indicated amount and sketch the result in the space provided.…

A:

Q: Locate the centroid of the given area below. Semi-Circle Square

A:

Q: In the figure below, find the SAB 0 ,CAB OCF %D

A: Given data E=200000MPa P=36kN

Q: Assessment 1. Using your knowledge in geometry and the second direction of making lines (Direction…

A: Assessment : 1 Using your knowledge in geometry and the second direction of making lines (Direction…

Q: DETERMINE THE LOCATION OF CENTROIDAL X AND Y. NOTE: UNITS ARE IN INCHES

A:

Q: express each common fraction as a decimal fraction. 5⁄64

A: Given data:- The given each common fraction is, 564

Q: Complete the table below. LINE BEARING DIST (M) AB N 58° 46.9' E 38.588 37.736 BC S 57° 59.7' E CD S…

A: Line Bearing Azimuth from North  θ Distance  l Latitude = l cosθ Departure = l sinθ AB N58°46.9'E…

Q: multiply the numbers 19 *65

A: Given:- Two numbers are given  1) 19  2) 65  To calculate:- The multiplication of given two numbers

Q: ntroduce the importance of gradation curve

A:

Q: An area (30*20) km has to be drawn on a sheet of paper (60*40)cm, find the required scale. 3/ Find…

A:

Q: express each common fraction as a decimal fraction 7⁄40

A: Given data:- The given fraction is, =740

Q: Determine the centroid x and y

A:

Q: area bounded by x=x^2 and y=9

A: