1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm". 1-10. A bar of variable cross section, held on the left, is subjected to three forces,P=4 kN, P. = -2 KN, and P, = 3 KN.as shown in the figure. On two separate diagrams,plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm?, and A3, = 150mm".P. PAzAjFig. Pl-10

Force is the measuring value of the response to such a load or displacement from a template or to…

1-10. A bar of variable cross section, held on the left, is subjected to three forces, P4 KN, P.-2 KN, and P.3 kN.as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, 200 mm, A2, - 100mm, and A3,- 150 mm".

1-10. A bar of variable cross section, held on the left, is subjected to three forces, P4 KN, P.-2 KN, and P.3 kN.as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, 200 mm, A2, - 100mm, and A3,- 150 mm".

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

respectively. E = 2.1 x 10 N/mm? and Poisson's ratio u = 0.3. Determine the magnitude of the In a stressed member 30 principal stress. 445 10" 1..eion: 30 32 10
7) The load P is located midway between points B and C. P = 1.7 kN. The diameter of the rod at CE is 4.8 mm. The young's modulus of the rod metal = 200 GPa. What is the elongation of the rod CE? 600 mm IB 600 mm 600 mm Elongation of rod EC = units
Use x = 137 y = 37 a = 6 b = 8 c = 1
The cantilever beam shown has a rectangular cross section with dimensions b = 25 mm and h = 100 mm, and is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a as shown. The beam is made of steel with E = 200 GPa and v= 1/3. Two strain gages are placed at point C, which is also at midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle ß= 60°. The measured strains are &a= 125 µɛ, &b = -375 με. Determine: a) The force P in kN [Ans. to check: P = 125 kN] b) The angle a in degrees. B b←
12. The bell crank, which is in equilibrium under the forces P and F = 36 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress (in MPa) in the pin if it is 21-mm-diameter. P is not equal to F. Round off to two decimal places.
2. The hinge support at A and steel rod at B support the horizontal rigid bar (neglect the weight of the bar) as shown. Determine the maximum vertical force P that can be applied at the end of the bar at C if the allowable stress in the steel rod is 35 ksi and the vertical displacement at C is limited to 0.12 in. Use 2 decimal places. (25 pts) steel L = 4 ft A = 0.5 in? E = 29 × 10° psi P =? A B C 3 ft 2 ft
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 11000 psi, and the vertical deflection of joint D is not to exceed 0.650 in. when a load of P = 3300 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 94 in., b = 22 in., and c = 32 in.
X= 460 lb. Find the stress at points A and B. Determine the point where the neutral axis intersects like ABD. The neutral axis intersects AB at (blank) inches from A and intersects BD at (blank) inches from D.