A centrifugal pump used to take water from reservoir to another through 800 m length and 0.15 m i.d. if the difference in two tank is 8 m, calculate the flow rate of the water and the power required, assume f =0.004. Q (m3 /h) 0 23 46 69 92 115 Δh (m) 17 16 13.5 10.5 6.6 2.0 η 0 0.495 0.61 0.63 0.53 0.1

Q: The efficiency at the best operating point is:

A: The best operating point is that point at which a pump is least prone or least probable to failure…

Q: 7. Water from the reservoir is pumped over hill through a 90 cm diameter pipe, and the pressure of…

A: Solution: Given Data: *The diameter of the pipe is, D=90 cm *The pressure at the summit is, P=200…

Q: Milk with a viscosity of μ-3 cP and density p=1060 kg/m³ flows through the pipeline from point 1 to…

A: the problem regarding the milk flow in the pipeline depicted in the image.Given information:Milk…

Q: B- A centrifugal fan connected to air duct system, the static losses in the duct is 100 N/m2 and the…

A:

Q: A crude oil is to be pumped out through a pipeline at flow velocity, v of 5 m/s. As a process…

A: Spring diaphragm is a simple mechanism.

Q: Modern wind turbine generator has a rotor blade diameter of 120 m, situated at sea level;…

A: Wind energy Wind energy is used to generate electricity. Wind energy is a non conventional form of…

Q: Ah against capacity Q pump and system curves for both pumps running on the basis of the O1. Two…

A:

Q: Head, m Consider the plot below, what is the operating flow rate of the pump in this ?system 25 20…

A: To determine the operating flow rate of the given pump.

Q: Laboratory tests on a centrifugal pump, which is directly coupled to a motor running at constant…

A:

Q: The blades on the radial-flow pump shown in (Figure 1) rotate at w = 200 rad/s. The blades are 2 in.…

A:

Q: what is the efficiency? what is the NPSHR? what is the motor power requirement?

A: (1):EFFICIENCY- The term efficiency can be characterized as the capacity to accomplish a ultimate…

Q: A hydraulic ram pump lifts 0.005 m3/s of water to a tank 20 m above the ram through a 80 m long and…

A:

Q: Determine the velocity in the discharge side. Determine the velocity on the suction side. Determine…

A:

Q: A turbine is located at an elevation 200 m. below the surface of the water intake. The friction loss…

A:

Q: Q11 Calculate the power required for a water pump used in a closed system with a flow rate Q=0.0076…

A: Detailed explanation:Given ValuesInlet gauge pressure=147 kPaOutlet gauge pressure=250 kPaFlow…

Q: static efficiency

A: Q=1500 ft3/min=25ft3/s=.71 m3/s γw=specific weight of water=9.81kN/m3 γa=specific weight of…

Q: 2 for the system shown in Figure 2, the parameters of pump and motor are as follows: maximal…

A: According to the given information of the system, we have the following parameters which are given…

Q: ancellation and do not use shift solv

A: Given-Information:- ρ = 875 kg/m3∆P = p1-p2=78 psi = 6032.91 kN/m2d1 = 25.4 mm =0.0254 md3 =0.20…

Q: A centrifugal pump has the following characteristics: V (m³/h) H (m) n (%) 23 46 69 92 115 16 13.5 2…

A: Given:Pipe length, L=800 mDiameter of pipe, d=15 cm or 0.15 mstatic head, hs=8 mTemperature of…

Q: A pump, geometrically similar to the 12.95-in model inFig. , has a diameter of 24 in and is to…

A: For water, ρ1 = 1.94 slug.ft3For gasoline, from Table A.3, ρ2 = 680 kg/m3 = 1.32 slug.ft3 From…

Q: Develop an introduction to a fluid pumping project, which aims to experimentally find the…

A: Step 1: Understand the project scope by finding the characteristic curves of the pump for your…

Q: 2. A fan draws 1.42 m^3 per second of air at a static pressure of 2.54 cm of water through a duct…

A:

Q: Two identical centrifugal pumps connected in series are used to pump water between two storage tanks…

A: Inner diameter of pipe, d=0.1 mTotal Equivalent length on the suction side, Ls=20 mTotal Equivalent…

Q: A system has a volume flow rate requirement of 2lit/s with an 60k Pa. Find an appropriate pump index…

A: Solution to first question as per our company policy:

Q: B) The air flow to a four cylinder four-stroke engine is 2.15 m³/min. During a test on the engine-…

A: In four stroke engine, there are four strokes which competes the cycle.The four processes are:(i)…

Q: TOSSIDLLTOINT3. 2J mp discharges 75 gallons per minute of water whose specific weight is 61.5…

A:

Q: II. Example TDH & WHP Calculation Determine TDH and WHP for a centrifugal pump discharging into the…

A: Solution:

Q: A nozzle having a velocity coefficient of 0.98 discharges a jet 15 cm in diameter under a head of…

A:

Q: 8.59 Two tanks A and B, of constant cross-sectiona! area of 10 m² and 2.5 m², respectively, are…

A:

Q: Three immiscible fluiids are contained in a tank: 1.0 m of water, 1.20 m of oil (s= 0.80) and air…

A: For solution refer below images.

Q: Estimate pump power requirement for Hpump = 58.598 m and npump = 0.60. Use the following: v = 1 x…

A:

Q: A reciprocating pump has the following data: Piston diameter.. Stroke.... Suction pipe length..…

A:

Q: A turbopump features the characteristic diagram reported below and operates at Q= 500 m /h. Evaluate…

A: The data corresponding to 500 m3/h flow rate from the graph is

Q: 1. To model power production in a traditional hydroelectricity unit, we can use the below schematic…

A: Given: The density of water, ρ = 998 kg/m^3 The dynamic viscosity, µ = 0.001 kg/ms The tank…

Q: H.W. 1- Repeat example 5.6 with Q₁ = 850 lit/min, Ah₁ = 40 m, N = 1450 rpm, and Power = 15 hp. 2-…

A: GivenQ1=850 ltr/minQ1=0.85060 m3/s∆h1=40mN=1450rpmP=15hp