A crude oil is to be pumped out through a pipeline at flow velocity, v of 5 m/s. As a process engineer, you are required to propose a suitable radius for the pipeline to be used if the volume flow rate, Q cannot be lower than 0.1 m3/s.

A crude oil is to be pumped out through a pipeline at flow velocity, v of 5 m/s. As a process engineer, you are required to propose a suitable radius for the pipeline to be used if the volume flow rate, Q cannot be lower than 0.1 m3/s.

Name: The following are general features of Spring & Diaphragm EXCEPTА.Simp
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The following are general features of Spring & Diaphragm EXCEPTА.Simple mechanismВ.Cost effectiveC.Based on air pressureRequire electric supplyD. A crude oil is to be pumped out through a pipeline at flow velocity, v of 5 m/s. As a process engineer,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The initially closed valve in Figure IIIb.6.1 (b) suddenly opens. Find the time it takes velocity to reach 99% of its steady-state value. Assume that fluid is inviscid and L = 30 ft, ho = 7 ft, D = 1 in. [Ans.: 7.5 s]
I need the answer quickly
In a refinery oil (s=0.85, 9=1.8 x 10-5 m2/s) flows through a 100 mm diameter pipe at 0.50 L/s, Find the center line velocity, the velocity at r=20mm, the friction factor , the shear stress at pipe wall and the head loss per meter of the pipe length.
2. A fan discharges 265 cu.m/min of air through a duct of 92 cm in diameter against a static pressure of 0.022 m of water. The fluid density is 995 kg/cu.m., the air temperature is 29°C and the barometric pressure reading is 730 mm Hg. If the power input to the fan is measured 3.5 hp, what are the total and static fan efficiencies?
Air flows steadily from a tank pressurized to 3kPa through a pipe of diameter D = 0.03 m and finally discharges to the atmosphere through a nozzle of diameter 0.01m. If the specific weight of air is 12 N/m^3 the air flow rate is?
8.59 Two tanks A and B, of constant cross-sectional area of 10 m² and 2.5 m², respectively, are connected by a 5 cm pipe, 100 m long, with f = 0.03. If the initial difference of water levels is 3 m, how long will it take for 2.5 m³ of water to flow from A to B? Considering entry and exit losses, it can be grossly assumed that the flow velocity, in m/s, through the pipe is 1.75√h, where his in m, taking g = 10 m/sec², also, may take area of pipe as 2 x 10-3 m².
6.4
Answer the problem correctly and provide complete and readable solutions. If you can explain the process (briefly), please do so. Thank you!
Air at 1 atm and 20 C flows through a smooth pipe. The centerline velocity and the pipe diameter are 6 m/s and 15 cm, respectively. Find a) the wall shear stress and b) the average velocity in the pipe.
Q 2. Air at 400°C and 1.7 bar flows through a horizontal 8.2-cm ID pipe at a velocity of 50.0 m/s. I. Calculate Ék (W)? Assuming ideal gas behavior and Mol.Wt (Air)=29 g/mol. I. If the air is cooled to 250°C at constant pressure, what is AER? III. Why would it be incorrect to say that the rate of transfer of heat to the gas must equal the rate of change of kinetic energy?
The figure shown below is a series pipeline system used to draw a fluid from a lower source open tank to a higher destination open tank . The flow and geometric layout for the system are listed below: Fluid: water Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m of two free surfaces Suction line: DN100 Sch. 40 Steel pipe Length: Ls=2.0 m Valve1: hinged disc type foot valve Entrance type: well-rounded Discharge line: DN80 Sch. 40 Steel pipe Length: Ld=100 m Valve2: full open gate valve Elbows: 90ο long radius elbow (1) Select the simplified general energy equations for section 1 and 2_________ A. B. C. D.
Q2: By using the General flow equation: Rew d 0.5 (P? - GT;LZ Q = 38.77F D².5 Approve that, for two parallel gas pipelines (1- BCE & 2-BDE ) as shown in the figure below, the equivalent pipe diameter for both pipelines can be determined by the following equation: 1/5 K. 1+ const1 K D, = D1 const1 where A E K2 (D 5 La constl =