1 A car engine has its rated output of 120 kW. The maxdmumtorque developed is 110 Nm, The clutch used is of singleplate type having two active surfaces. Axia! pressure is not toexceed 0.85 bar. External diamater of friction plate is1.25 times the internal diameter. Determine the dimensionsof friction plate and axial force exerted by the spring.Assume uniform wear and coefficient of friction to be 0.3.

Answer: ◆ The dimensions of the friction plate are: Outer radius : ro = 133.75 mm and inner radius :…

A car engine has its rated output of 120 kW. The maxdmum - torque developed is 110 Nm, The clutch used is of single plate type having two active surfaces. Axial pressure is not to exceed 0.85 bar. External diameter of friction plate is 1.25 times the internal diameter. Determine the dimenslons of friction plate and axial force exerted by the spring. Assume uniform wear and coefficient of friction to be O.3.

A car engine has its rated output of 120 kW. The maxdmum - torque developed is 110 Nm, The clutch used is of single plate type having two active surfaces. Axial pressure is not to exceed 0.85 bar. External diameter of friction plate is 1.25 times the internal diameter. Determine the dimenslons of friction plate and axial force exerted by the spring. Assume uniform wear and coefficient of friction to be O.3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2/ A dry single plate clutch is to be designed for an autontotive vehicle whase engine is ated to give 100 &W at 2400 r.p.M. and marimum torque 500 N-m. The outer radus of the friction plate is 25% ore than the inner radius, The intensity of pressure berween the plate is not to exceed 0.07 N/mm. The coefficient of friction may be assamed egual t0 0.3 The helical springs reguired by this cluich to provide axial force mecessary to engage the clutch are eight. If cach spring has stiffness equal to 40 N/mm, derermine the dimensions of the friction plate and initial compression in the springs
" BELT FRICTION " Please include FBD and Solution please thankyou!
A multiple disc clutch has radial width of the friction material as 1/5th of the maximum radius. The coefficient of friction is 0.25. Find the total number of discs required to transmit 60 kW at 3000 r.p.m. The maximum diameter of the clutch is 250 mm and the axial force is limited to 600 N. Also find the mean unit pressure on each contact surface.
A multi-disk clutch consists of two steel disks with one bronze disk. Theinner and outer diameters of the contacting surfaces are 200 and 250 mmrespectively. The coefficient of friction is 0.1 and the maximum pressurebetween the contacting surfaces is limited to 0.4 N/mm2. Assuming uniformwear theory, calculate the required force to engage the clutch and the powertransmitting capacity at 720 rpm
A multiplate friction clutch is required to transmit 72 kW at 3600 r.p.m. The plates are alternately steel and phosphor bronze and they run in oil. The coefficient of friction is 0.071. The mean axial pressure is 0.14 N/mm? and the internal radius of the friction surfaces is 0.8 of the external radius, which is 125 mm. Find out the number of plates reauirod
A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250 mm and the inner diameter is 150 mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75 kW at 500 r.p.m. Assume uniform wear and coefficient of friction as 0.3.
The coefficient of static friction under the block a and b are the same. If the block is in the verge of sliding, find the tension at each chord. Assume that the pulley is frictionless.Recall [from Physics]:?? = ???Where:?? - is the frictional force?? - is the normal force? -coefficient of static frictiona. Determine the tensile force (lb) on the cable 1.b. Determine the tensile force (lb) on the cable 2. Plsss show complete handwritten solution. Thanksss!!
2. A square threaded screw of mean diameter 25 mm and pitch of thread 6 mm is utilised to lift a weight of 10 kN by a horizontal force applied at the circumference of the screw. Find the magnitude of the [Ans. 966 N] force if the coefficient of friction between the nut and screw is 0.02. A bolt with a squore threaded screw has mean diameter of 25 mm and a nitch of 23 mm It carries an
A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has aface angle of 10◦The width of the face is halfe of the mean radius and the max pressureis 0.1 N/mm²Assuming uniform wear and the coefficient of friction is 0.3, find theinner and outer radius and the axial force required on the clutch. Subject: Theory of Machines
A cone clutch has cone elements at an angle of 12o. The clutch transmit 25 HP at a speed of 1200 rpm. The mean diameter of the conical friction section is 16 in and the coefficient of friction is 0.35. Find the axial force needed to engage the clutch.
Machine Elements
Determine the principal dimensions of a cone clutch faced with lather to transmit 40 kW at 800 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions. Assume that the semi-angle of the cone is 10°, the coefficient of friction is 0.3, mean diameter of cone is (7-10)d, where d is the diameter of the shaft, allowable normal pressure for lather and cast iron is 0.1 to 0.2 N/mm, shear stress 100 N/mm², load factor is 2 and the mean diameter to face width ratio is 6.