A can of paint (10 lb) and a painter (180 lb) are positioned on a step latter. Compute the forces at each connection. Model the step ladder as the 3 members shown, with friction at support A and a frictionless connection at B. The distance EG is 1.5 ft and CF is 1 ft. G W2 F C 0.6 ft 3 ft 15° B

A can of paint (10 lb) and a painter (180 lb) are positioned on a step latter. Compute the forces at each connection. Model the step ladder as the 3 members shown, with friction at support A and a frictionless connection at B. The distance EG is 1.5 ft and CF is 1 ft. G W2 F C 0.6 ft 3 ft 15° B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Note: Hi, pls need help. Any solutions are highly appreciated. I will rate this right away. Thank you in advance! What is the interaction value for combined moment? Considering sag rods and tie rods at third points (2 decimal places) A 20m Fink Truss are spaced at 'S' meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is 'RLL' N/m2 of roof surface and roof covering is assumed to be 'RDL' N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings.
Can I please get full workings out for this past paper question please. I just need help with part 2
Q.1//The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is applied. The connection at A is a pin, and AB is supported on the steel rod BE and the copper rod CF. The length of BE & CF is 250 mm. The cross sectional area of CF is 400 mm', the area of BE is 200 mm. Determine the stress in each of the vertical rods . The weights of all bars are negligible. For copper E=120 GPa, for steel E=200 GPa. 200 KN B. 1.5 m 500 mm 11500 mm 250 mm steel сорper
Problem 50 Two forces of magnitude T, = 10kips and Tc =15kips are applied as shown to a welded connection. Knowing that the connection is in equilibrium, determine the magnitudes of the forces T, and Tp-
1.45 A roof truss and the detail of the connection at joint B are shown in the figure. Angle sections with the thicknesses shown in the figure are members BC and BE. Shear in the rivets has a working stress of 70 MPa, while bearing stress due to the rivets has a working stress of 140 MPa. To fasten the following members to the gusset plate, how many 19-mm-diameter rivets are required: (a) BC; and (b) BE? 14mm-thick gusset plate 13mm-thick angle bar 6m 6mm-thick BE angle bar C. 3m 3m 3m 3m Рвс 100KN 200kN 100KN
The rigid bar AC is to lift a weight W at C and is supported by pin at A and strut DB at B as shown in figure A. For this problem, use L1=2.3m, L2=2.2m, H=4m and W=6kN. All types of connections is typically shown in figure B. What is the required diameter of Bolt at B if the allowable shearing stress is 40 MPa?
The cutaway view shows a solid aluminum alloy [L2 = 800 mm; A2 = 667 mm2; E2 = 70 GPa] rod (2) within a closed-end bronze [L1 = 818 mm; A1 = 1211 mm2; E1 = 100 GPa] tube (1). Before the load P is applied, there is a clearance of 3 mm between the rod flange at B and the tube closure at A. After load P = 220 kN is applied, rod (2) stretches enough so that flange B contacts the closed end of the tube at A. Calculate the internal force in bronze tube (1).
The following support is called: O a. Roller O b. Hinge O c. Fixed O d. Rocker
The lower ends of the three bars are at the same level before the uniform rigid block weighing 40 kips is attached. Each steel bar has a length of 3 ft, and area of 1.0 in2, and E = 29 x 106 psi. For the bronze bar, the are is 1.5 in2 and E = 12 x 106 psi. Determine: (a) the length of the bronze bar so that the load on each steer bar is twice the load on the bronze bar. (b) the length of the bronze that will make the steel stress twice the bronze stress.
Whats the free body diagram on this problem.
The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the weld CANNOT exceed 3 in. If the weld must transmit a total force equal to 9600 lb. Its size should be A. 1/2 in B. 3/8 in C. 5/16 in D. 1/4 in
The plate shown in the figure is fastened to the fix member by three 10 mm diameter rivets. Compute the value of the loads P so that the shearing stress of any rivet does not exceed 70 Mpa.