A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal before the load P is applied. Bars (1) and (2) are both made from steel [E = 30,000 ksi] and both have a cross-sectional area of 1.25 in.2. If the normal stress in bar (1) must be limited to 18 ksi, determine the maximum load P that may be applied to the rigid bar.

A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal before the load P is applied. Bars (1) and (2) are both made from steel [E = 30,000 ksi] and both have a cross-sectional area of 1.25 in.2. If the normal stress in bar (1) must be limited to 18 ksi, determine the maximum load P that may be applied to the rigid bar.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

9. Grace loves to eat salad. How many salads can she put together if she can pick out one type of lettuce from 2 choices, one vegetable from 4 choices and one dressing from 7 choices?
Answer 4 5 6 handwritten then box the final answer
The isosceles triangle gate shown in the figure is hinged at A and filled with water. What is the hydrostatic force (kN) acting on one side of the gate? a=1m, b=5.16m, c=2.09m
Instruction: Express your intermediate answers with at least FOUR decimal places and simplify your FINAL answers up to TWO DECIMAL PLACES. BOX your FINAL ANSWERS. Start each problem on a new answer sheet. State all your assumptions and show complete solutions. Follow the guidelines for the answer sheets, as indicated in the Course Format. Work on the problems independently. Problem 1. The frame is loaded as shown in the figure. The joints B and C are fixed connections while A is supported at by a roller and point B is hinged. Determine the following: a. Determine the support and pin reactions of the frame below. b. Sketch its shear and moment diagrams. c. Determine the value and location of maximum shear and moment of the beam. 4.0 m B Y 11 kN/m Y 5.0 m- W C -3.0 m 24 kN/m
( Hand written and clean writing )
Solve the problems on a clean sheet of paper. Follow the Given-Required-Analysis-Solution-Summary of Answers format. Make sure to include all pertinent solutions. Round your final answers to three (3) decimal places. For example, if you calculated an answer to be “9.80665” it should be expressed as “9.807”.
Answer A and B without excel. Show all steps.
30 Material Science and Engineering
Please answer asap with correct, clear and complete solutions. Asap. Thank you
** Please label the question answers so I can understand better! Thanks! Scenario: A chair with a mass of 20.0 kg is attached to one end of a frictionless pulley system via a strong massless rope. The other end of the rope is attached to a steel water tank sitting on a flat horizontal concrete surface (see the image to the right). The coefficient of static friction between steel and concrete is 0.45 and the coefficient of kinetic friction between the surfaces is 0.30. The water tank, which is full of water, has sprung a leak. The combined mass of the water and the tank is 500 kg. This mass slowly decreases as the water leaks from the hole. You (i.e. my mass is 55.7 KG) are sitting at rest in the seat. You and the seat will remain at rest as long as the force of static friction is strong enough to hold you. Task: LET [DOWN] and [RIGHT] be positive. Using your knowledge of physics, determine the following: 1. As soon as the chair begins to move, static friction between the steel…
Write an 80 word paragraph about only one of the following topics. Your paragraph should include a paragraph title, a topic sentence, a minimum of three supporting sentences with supporting details and a concluding sentence. Use suitable transition devices to achieve coherence. 1. The negative effects of air pollution. 2. The most comfortable means of transport. 3. Solutions to keep the environment clean. 4. How to prepare your favourite dish.
Using Virtual Work Method Find the smallest value of P acting at the FD midspan that is required in order to get a zero deflection at point B. For two steel beams EI = 400,000 kNm² Please box your final answers I'll thumbs up on the correct answer. please see the note, below before answering. Final answers in the solution sheet should be rounded to three (3) decimal places and should be enclosed in a rectangle for easy identification. Final answers for locations or distances must be given in meters or feet. Final responses for deflections must be given in millimeters or inches. NOTE: No final solutions shall be in scientific notation. Final answers for slopes shall be in degrees to 5 decimal places.