A calibration test of a 12.7 mm circular sharp-edged orifice in the vertical side of a large tank showed a discharge of 587 N of water in 81 seconds at a constant head of 4.70 meters. Measurement of the water jet showed that it traveled 2.35 meters horizontally while dropping 30.50 centimeters. Determine the three orifice coefficients and draw the figure. Note: determine each coefficient independent from the other coefficients, solve them as equal to the ratio of the actual quantity to the theoretical quantity. No credit points for direct formula substitution solution

Q: The cross-section of a concrete dam, with consistent density and after draw down, is shown in the…

A:

Q: Determine the magnitude and direction of the velocity of collars A and  B after the impact as a…

A:

Q: Q. A bar 500 mm long and 30 mm in diameter hangs vertically and has a collar securely attached at…

A: L=500mm d=30mm P=150N h=60mm To find stress induced

Q: Q. A bar 500 mm long and 30 mm in diameter hangs vertically and has a collar securely attached at…

A:

Q: A horizontal jet strikes a frictionless vertical plate the plan view is shown in the figure). It is…

A:

Q: b) The following information has been collected in the lab during "Head Loss in Bends and Fittings"…

A: Part B answer Given data Manometer readings for sections before and after a bend: h1=326 mm and h 2=…

Q: 5. A finite difference flow model well. Is the model-predicted head likely to be higher or lower…

A: To determine flow rates, flow direction, and hydraulic heads through an aquifer, the finite…

Q: 26. An increase in pressure tends to increase the boiling point of liqui- This relationship denotes…

A: With decrease in pressure the boiling point decreases because the molecules need less speed to…

Q: Figure below shows a rod that supports a mechanism for food manufacturing company. Given that the…

A: Given data,  P = 2250 N A =  125 mm B = 200 mm C =165 mm D = 85 mm Diameter of rod = 6.5 mm To find…

Q: Q. A bar 500 mm long and 30 mm in diameter hangs vertically and has a collar securely attached at…

A: Given data:L=500 mmd=30 mm W=150 Nh=60 mm E=2 x 105N/mm2

Q: a 12. circular sharp-edged orifice in the A calibration test of a mm vertical side of a large tank…

A: Diameter of orifice =12.7mm Time(t)=81sec

Q: A well in an unconfined aquifer was pumped at a rate of 900 m³/day. Drawdown was measured in a fully…

A: Given, Flow rate (Q) = 900 m3/day Radial distance (r) = 85 m

Q: е. 650 ton of Sample1 and 150 ton of Sample 2 are available. How many Kg of particle size bigger…

A: e. Calculate the % of retained for each sample. Calculate the same proportion with 650 ton of Sample…

Q: It takes a vertical force of F= 75,000 lb to separate the two parts at A and C in (Figure 1). Figure…

A: Given, F=75,000 lbμs=0.2to determine,P

Q: c) Name the fitting from the lab experiment (excluding the valve) that should have the highest head…

A: In laboratory experiments involving fluid flow, the fittings used can have a significant impact on…

Q: Example 6.13 For the following functions in two-dimensional irrotational flow, determine the…

A:

Q: SITUATION: In order to determine the volume and the specific gravity of a stone that weighs 45 kg in…

A:

Q: The cross-section of a concrete dam, with consistent density and after draw down, is shown in the…

A:

Q: Choose the letter of the correct answer. Please answer honestly and do not just guess. In the Moody…

A: Qm(1) = in the moody diagram the reylonds no of axis is in linear scale    Q(2) = friction factor…

Q: A

A:

Q: The cross-section of a concrete dam, with consistent density and after draw down, is shown in the…

A: Given data  d = 0.71 m  h = 9.37 m

Q: The balls A and B in the figure are attached to stiff rods of negligible weight. Ball A is released…

A: Given, coefficient of restitution, e=0.6 impact lasts for 0.01 sec To determine, angle θ

Q: Solve the following beam by the conjugate beam method, calculate its maximum deflections, write the…

A:

Q: Consider the system shown in the figure. If a change of P kPa in the pressure of air causes the…

A: Given  P= 35 kPa d= 7mm   To find The ratio of A2/A1

Q: For the shaded area shown, Use R = 6 cm, and r = 4.5 cm. a. determine the moment of inertia with…

A:

Q: A vibration test was conducted on the model of a tank. A cable attached to the tank induced a force…

A:

Q: Prob-7 Density of gauge fluid used in well manometer is p =8000±10.0 Kg/m³. The maximum height of…

A: Density (ρ) = 8000 ± 10.0 Kg/m3 (0.125%) Maximum Height of reading scale H =0.8m ± 0.2 mm (0.025%)…

Q: How can water displacement be used to measure the density of a non-porous irregularly shaped solid?

A:

Q: 1. From the figure shown, two blocks weighing 150 N and resting on a horizontal surface are to be…

A:

Q: then the total displacement

A: FALSE

Q: 7. A particle travels along a straight-line path such that in 4secs it moves from an initial…

A:

Q: What will be the value of reduction factor R1 if value of At is given to be 500 ft2 ? (a) 0.5 (b)…

A: ASKED: To determine the value of reduction factor R1 for given value of tributary area.   Given,…

Q: Question 1 %3D Determine the magnitude of Q if the particle is in equilibrium and if e =19.8°, P =…

A: Given data, P = 271 N θP=19.8o a = 2 b = 13 θQ=tan-1(213)=8.746o

Q: The cross-section of a concrete dam, with consistent density and after draw down, is shown in the…

A:

Q: In the figure, a small 0.309 kg block slides down a frictionless surface through height h = 0.478 m…

A: Step 1:

Q: Situation 04. The acceleration of a particle is given by a = 3t - 2. a. Find the initial velocity…

A:

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.