a 12. circular sharp-edged orifice in the A calibration test of a mm vertical side of a large tank showed discharge of 587 N of water in 81 seconds at a constant head of 4.70 meters. Measurement of the water jet showed that it traveled 2.35 meters horizontally while dropping 30.50 centimeters. Determine the three orifice coefficients and draw the figure. Note: determine each coefficient independent from the other coefficients, solve them as equal to the ratio of the actual quantity to the theoretical guantity

a 12. circular sharp-edged orifice in the A calibration test of a mm vertical side of a large tank showed discharge of 587 N of water in 81 seconds at a constant head of 4.70 meters. Measurement of the water jet showed that it traveled 2.35 meters horizontally while dropping 30.50 centimeters. Determine the three orifice coefficients and draw the figure. Note: determine each coefficient independent from the other coefficients, solve them as equal to the ratio of the actual quantity to the theoretical guantity

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular tank 3 m x 4 m is 5 m high with 2 orifices placed at a vertical distances of 0.5 m and 1m from the bottom respectively. Both orifices are 100 mm diameter with C=0.607. Determine the: show complete solution a. How long will it take to lower the water at tank by 2 m in seconds?b. How long will it take for the water surface to be at the same level as the upper orifice in seconds?
Energy Loss in Bends and Fittings a) What is the difference between major loss and minor losses in a pipe network? Give at least three examples of minor losses? b) The following information has been collected in the lab during "Head Loss in Bends and Fittings" experiment: Manometer readings for sections before and after a bend: h₁=326 mm and h₂=253 mm Q=0.28 lit/s Pipe diameter 1.83 cm Calculate the head loss coefficient (K) for this bend. - c) Name the fitting from the lab experiment (excluding the valve) that should have the highest head loss and explain why this is the case?
A cylinder weighing 20 pounds slides in a free pipe as shown in the figure. The clearance between the cylinder and the pipe is 0.001 in and it is filled with oil of relative gravity 0.80. If the cylinder is observed to decelerate at the rate of 2 ft/s^2 when the speed is 20 ft/s. Calculate dynamic and kinematic viscosity W = 20lb u = ? %3D %3D S oil = 0.80 p = ? %3D V = 20ft/s %D ccciinther Bripelgne epinder 5 inches
In figure 2.5, if the pressure of gas in bulb A is 50 cm Hg vacuum and Patm = 76 cm Hg, the height of column H is equal to (a) 26 cm (c) 76 cm Patm 144.444 Hg= (b) 50 cm (d) 126 cm arter
Question 3: A lab test was used to identify the headloss coefficient of a confusor k'e where: h = kE' ,V² -V₂² 2g that is shown in the figure. Two pizometers were installed at A1 and A2, which measured piezometric head of 40 cm and 44 cm, respectively. The diameters are 5 cm, and 10 cm at A1 and A2 respectively Flow was measured as 0.02 m³/s. Find kE' V₁- A1 a A2 -V₂
A calibration test of a 12.7 mm circular sharp-edged orifice in the vertical side of a large tank showed a discharge of 587 N of water in 81 seconds at a constant head of 4.70 meters. Measurement of the water jet showed that it traveled 2.35 meters horizontally while dropping 30.50 centimeters. Determine the three orifice coefficients and draw the figure. Note: determine each coefficient independent from the other coefficients, solve them as equal to the ratio of the actual quantity to the theoretical quantity. No credit points for direct formula substitution solutions.
7. Two water tanks are connected to each other through a mercury manometer with inclined tubes, as shown in figure. If the pressure difference between the two tanks is 20 kPa, determine the value of ? in degrees. (2 decimal)