A brief, deep cantilever pillar is 500 mm long by 200 mm deep and is 2 mm thick. It carries a vertically descending load of 35 kN at its end. Expecting that the shear push is consistently dispersed over the cross area of the bar. Which of the following gives the uniform shear strain of the beam in radians if the shear modulus or Modulus of Rigidity G=25000 N/mm^2

A brief, deep cantilever pillar is 500 mm long by 200 mm deep and is 2 mm thick. It carries a vertically descending load of 35 kN at its end. Expecting that the shear push is consistently dispersed over the cross area of the bar. Which of the following gives the uniform shear strain of the beam in radians if the shear modulus or Modulus of Rigidity G=25000 N/mm^2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a simply supported beam is carrying a varying load and a uniform load as shown in the figure. If the beam properties are given below, what is the final stress at bottom of beam section at a distance 2.47m from the right support where the totall losses of the prestressing force is 24% mpa beam wid=217mm height= 480mm varying load= 9.67kn/m uniform load = 4.27 kn/m x = 3.32 y = 5.95 Prestressing force = 429kn eccentricity = 95mm
A hollow aluminum box beam has the square cross- section shown in the figure. Calculate the maximum and minimum shear stresses max and min in the webs of beam due to a shear force V = 125 kN.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If σ = 11 MPa in the direction shown, determine the principal stresses at the point. 28.6 MPa and -33.6 MPa 20.7 MPa and -42.4 MPa 39.6 MPa and -46.7 MPa 26.8 MPa and -35.8 MPa 34.2 MPa and -40.0 MPa
The following stress element represents the stress state at point A of the structure in the figure below. Determine the maximum shear stress in this condition. 52.8 MPa 26.4 MPa O a. 32.78 MPa O b. 29.65 MPa Oc. 40.25 MPa O d. 37.34 MPa
Show FBD and geometry of deformation in solving the problem
Question 2 A simply supported beam of a channel section (see Figure Q2) is loaded by a vertical point load P= 10 kN (acting upwards) at mid-span. The length of the beam is L=3 m, the overall width and height of the section are of the same value a 50 mm, and the thickness of all three parts of the section is t= 10 mm. Find the value and location of the maximum shear stress in the beam. Figure Q2
QUESTION 3) A horizontal beam AD is supported by an inclined strut CB and carries a load of 15 kN at joint D in the figure. The strut, which consist of two bars each of thickness 40 mm, is connected to the beam by a rivet passing through the three bars meeting at joint C. The allowable shear stress and bearing stress are t-60 MPa and o=120 MPa, respectively. a) Determine the required diameter of the rivet at the hinge C that carry safely by the given system. b) If the diameter rivet used on the support A is 20 mm check whether this rivet diameter is sufficient for the given system. 0.8m Im 0.6m 15 kN В Beam AD 20mm Strut CB 40mm 100mm 40mm 50mm 100mm Detail of joint C Detail of joint A
2. The beam with cross-section shown carries a uniformly distributed load of intensity w over its entire length. Determine w if the allowable stresses are g = 40 MPa, g = 80 MPa, and t = | T 12 MPa. w (kN/m) 75 mm 10 mm 0.5 m : 10 mm 3m 10 mm- 150 mm 150 mm
Beam 9: (P = 26 KN - L = 2.0 metres) For the given cross section of the beam, find the magnitude of the maximum compressive bending stress and also the magnitude of the maximum tensile bending stress. What is the maximum shear stress in the beam and where in the beam does it occur? 2P 2P 25 50 25 25 50 125
Consider a fillet section subjected to a tensile force F. Knowing that the fillet section has a uniform thickness of 5 mm and a yielding stress of 250 MPa, determine the force F that initiated the yielding of the fillet section. a.1.25 kN b.2.5 kN c.4 kN F d.2 kN 40 mm 25 mm 40 mm ↓ Which of the following is FALSE regarding the equation for deformation, 8=PL/AE? A. The term AE refers to the resistance of the member against axial deformation B.It can be used even for non-prismatic members C.It can only be used to compute for the elastic axial deformation of the member D. The term P refers to the internal axial force at the section considered A rigid bar ABC is loaded and supported as shown in the figure. After the load P is applied, the deformation of bar BD, SBD 0.6mm. What is the displacement at point B? A.0.36 mm B.0.48 mm P C.0.75 mm D.1.00 mm C 0.3 m 0.3 m Which of the following statements is TRUE for a circular shaft under pure torsion? A. The angle of twist of a point on the…
1. For the beam showing in the figure, consider section n-n and determine; (a) The largest shearing stress in that section (b) The shearing stress at point a. 0.3 m 40 nim 10 KN 12 imm 150 mm 12 mm 200 mm 15 in
For the given beam section, determine the thickness of the point where the maximum horizontal shear stress will act on the beam.