A simply supported beam is carrying a uniform load. If the beam properties are given below, what is the final stress at top of the beam section at midspan where the total losses of the prestressing force is 27% (MPa)

A simply supported beam is carrying a uniform load. If the beam properties are given below, what is the final stress at top of the beam section at midspan where the total losses of the prestressing force is 27% (MPa)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
PROBLEM 1 A circular aluminum tube of L=600mm is loaded in by compressive forces at its ends. The outside and inside diameters are 75mm and 63mm respectively. A strain gage is placed on the outside of the tube to measure nomal strains in the longitudinal direction. E=73 GPa and Poisson's is 0.33. a. If the normal stress in the tube is 57 MPa, what is the load P? b. if the strain is 781 X 10-6, what is the shortening of the tube? What is the percent change in its cross-sectional area.
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
Strength For the state of plane stress shown, determine the largest value of o, for which the maximum in plane shear stress is equal to or less than 75 MPa. After you determine the value, draw Mohr circle for the case
A small aluminum alloy [E = 80 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P ЗР Strain gage d D E H Answer: P = i
A small aluminum alloy [E= 77 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 160 mm. The cross- sectional dimensions of the tee shape are b= 22 mm, d = 33 mm, and t= 4 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 uɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? %3D %3D %3D 3P Strain gage E Answer:
2. (3 points) When loading is applied at a point on a body, the stress distributions at different cross sections are different. However, the stress distribution becomes uniform at locations far from the applied load. This is due to which principle? Name the principle. P Load distorts lines located near load P P C C Lines located away from the load and support remain straight P O avg A section a-a section b-b section c-c -Load distorts lines located near support Your answer
A horizontal load P of magnitude 97 kN is applied to the beam shown. Determine the largest distance a for which the maximum tensile stress in the beam does not exceed 75 MPa. 20 mm 20 mm 20 mm y P O 60 mm 20 mm The largest distance a is mm.
2.75 A steel rod is stretched between two walls. At 20°C, the tensile force in the rod is 5000 N. If the stress is not to exceed 130 MPa at –20°C, find the minimum allowable diameter of the rod. Use a = 11.7 × 10–6/°C and E = 200 GPa. %3D
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 20.11 lb.
d. Calculate the bending stress in a layer 80 mm below the top surface of the beam at section B. e. Find the maximum bending stress.
The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.