A boom is pinned at A and supported by cable BC. If the weight of the boom is 500 kg, determine the magnitude of the force reaction at A and the tension in cable BC (in kilo-Newton) needed to support the 1-tonne load suspended at B. Assume that the center of mass of the boom is at mid-length. T 35° 5m

A boom is pinned at A and supported by cable BC. If the weight of the boom is 500 kg, determine the magnitude of the force reaction at A and the tension in cable BC (in kilo-Newton) needed to support the 1-tonne load suspended at B. Assume that the center of mass of the boom is at mid-length. T 35° 5m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A crane is oriented so that the end of the 25-m boom AO lies in the yz plane. At the instant shown, the tension in cable AB is 4 kN. Determine the moment about each of the coordinate axes of the force exerted on A by cable AB.
Current Attempt in Progress The vertical mast supports the 3.5-kN force F and is constrained by the two fixed cables BC and BD and by a ball-and-socket connection at A. Calculate the tension T1 in BD. Can this be accomplished by using only one equation of equilibrium? Assume a = 5.0 m, b = 4.3 m, c = 1.8 m, h = 4.6 m. | В T1 T2 D F b
The flexible cable used to tether the balloon shown in Fig. loon exerts a buoyant vertical force of 2000 N on the cable at end B. Determine weighs 7.0 N/m and is 100 m long. The bal- The horizontal distance d from the anchor A to the bal- loon. F wind B 30°
3. Determine the horizontal and vertical components of reaction at the pin A and the tension developed in cable BC used to support the steel frame. O AN O AN m
Problem#3: The frame shown supports part of the roof of a small building. Knowing that the tension in the cable is 150 kN, determine the reaction at the fixed end (which is a cantilever) E. A B 20 kN 20 kN 20 kN 20 kN 1.8 m 1.8 m 1.8 m 1.8 m E 4.5 m 2.25 m 3.75 m F
Problem 1: The load below is being lifted. And at 4 ft, having constant acceleration from its rest with an upward velocity of 3 ft/sec. The gear at A of the rotating motor drives gear B, which is attached to the rotating drum. Determine the : 1. acceleration of point C on the cable in contact with the rotating drum as the load passes this position. 2. angular velocity and angular acceleration of the gear at The gear at A of the rotating motor drives gear B, which is attached to the rotating drum. C 36 48 12 3 ft/sec L.
The assembly has a mass of 4 Mg and is hoisted using the winch at B. The boom has a mass of 2 Mg and mass center at G. Determine the greatest upward acceleration of the assembly so that the compressive force in the hydraulic cylinder supporting the boom does not exceed 182 kN. What is the tension in the supporting cable? 1m 4m B 2m 6m
2. The light right-angle boom which supports the 4KN cylinder is supported by the three cables and a ball-and-socket at O attached to the vertical x-y surface. Determine the reactions at O and the cable tensions. у 1.2m 1.5 m D C 1m E 1m A 2.2m B 0.75 m 0.75 m
lift sling is used to hoist a container having amass of 500 kg. Determine the force in each of the cablesAB and AC as a function of θ. If the maximum tensionallowed in each cable is 5 kN, determine the shortest lengthof cables AB and AC that can be used for the lift. The centerof gravity of the container is located at G.
7-115. The 80-m-long chain is fixed at its ends and hoisted at its midpoint B using a crane. If the chain has a weight of 0.5 kN/m, determine the minimum height h of the hook in order to lift the chain completely off the ground. What is the horizontal force at pin A or C when the chain is in this position? Hint: When h is a minimum, the slope at A and C is zero. B Asseccons 60 m Prob. 7-115
If the 75-kg crate starts from rest at A, determine its speed in m/s when it reaches point B. The cable is subjected to a constant force of F = 300N. Neglect friction and the size of the pulley. 30° F 6 m B A 6 m -2 m-
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 14i - 16j kN.Note that the reaction force at A acts along the boom because it is a two- force member. Calculate the magnitude of the reaction force at A in kN. 2m 4 m 6 m y A 6m u 7.