2. The light right-angle boom which supports the 4KN cylinder is supported by the three cables and a ball-and-socket at O attached to the vertical x-y surface. Determine the reactions at O and the cable tensions. у 1.2m 1.5 m D C 1m E 1m A 2.2m B 0.75 m 0.75 m

2. The light right-angle boom which supports the 4KN cylinder is supported by the three cables and a ball-and-socket at O attached to the vertical x-y surface. Determine the reactions at O and the cable tensions. у 1.2m 1.5 m D C 1m E 1m A 2.2m B 0.75 m 0.75 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the reaction at the support A (NA) of the compound beam. Assume there is a pin at C. 40 kN…

A: To find reaction at point A

Q: 5-27. The power transmission cable weighs 150 N/m. If h = 2.5 m, determine the resultant horizontal…

Q: A 200 m loading arm (AB) and a 240 m-diameter pulley are welded to the smooth bar BE that is…

A: Tension in a cable is defined as the force that is exerted in a cable. Measure of force is said to…

Q: 4) Write the equilibrium equations 5) Solve for the unknown exterior reactions. 3 m -3m- B F 60 kN…

Q: Compute the reactions of hinge and roller of eam AB. 2m 2m 2m 50 KN B A C cable D 50 KN-m F E 5 KN/m…

Q: Solve for the member forces

Q: 2

A: Given:- 4-16mm diameter Es=200GPa P=5kN To find:- Cable DE force resultant reaction at base of beam…

Q: A continuous beam is carrying a triangular load as shown. An internal hinge at B allows the system…

Q: 6m 5: |i| T 12 m 13 m N N B

Q: find moment at point D, P=15kN

A: Given:- FBd of Beam;

Q: A Construct influence line for 1. Reaction at B 2.5m 5m 2.5m B 5 m

Q: 2. The light right-angle boom which supports the 4KN cylinder is supported by the three cables and a…

Q: Find the reactions at A and B

Q: 5 kN 20 kN/m B. -211 3 m

Q: so IN 30 AN/in D B. 2 m 2 m

A: Given data:

Q: В 400 mm D A 600 mm 700 mm·

A: The coordinates of point A are (0.7, 0 ,0.6) To determine the coordinates of point B, we will have…

Q: 4. Compute for the reaction at the roller B, the force components acting on the ball- and-socket at…

Q: Q3. Determine the reactions at the pin ( A) and the roller ( B ). 80N 60 5m 150 N A 4 m 5m 3m FON Ý…

A: Balancing forces and moments

Q: The light right-angle boom which supports the 290-kg cylinder is supported by three çables and a…

Q: A 3.5 m D 7m B 2.5m *

Q: Problem No. . Draw the influeice line for the vertical reaction and moment at B. 5m 5m 5m ... O .

Q: Ah Av 60° hinge Block Center O of pulley D B 00 By rollers (B₁ = 0) W = 1,000 N (AC BD=1.00 m; CD =…

A: Given:AC=BD=1 mCD=2 mWeight of the block=1000 NSince, beam and pully are weightless.Therefore,We…

Q: 2. The center of gravity of the 50-kg spool is at G. A cable wound around the hub of the spool is…

Q: aft. Calculate the t

A: Apply equilibrium :∑ Fz=0T2(31.52+32)+T2(31.52+32)+T1=mg2T2(0.44721)+T1=480(9.81).....(1)

Q: Q2 The 2-kg collar A starts from rest in the position shown when a constant force F=100 N is applied…

Q: An AB lever is hinged at C and attached to the control cable at A. If a lever is found, a horizontal…

A: The given figure is shown below:

Q: PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B. Determine the…

A: Given data A and C are hinge support and pin at B. Find support reaction.

Q: Problemci) :- A(skN) cylinder is supported by beam AB and acable as shown in Fig.bleow.Detemine the…

Q: d the

A: Draw free body diagram From the above figure At point C, tanθ=21θ=tan-12θ=63.435o

Q: 1.5m 800 N/m 3 m B Im 1.5m tismt -1m²7 1.5 m 3m Solve for the reaction components at the ball and…

Q: For the cable shown, determine the vertical reaction at B (N). 12 m 12 m | 12 m 12 m Inc hp=8m hE…

Q: Analyze the structure below using cantilever beam method 25KN C 3m 50KNB H 4m 6m -8m- SOLVE the…

A: Given data in question Frame Horizontal loading To find out Centroidal distance from column ABC

Q: Find the following: (a) vertical reaction point C (b) vertical reaction point G (c) vertical…

A: Given:-

Q: Compute the reactions of the fixed support at Point D. 50 N 20 N / m 10 N/ m В 50 N-m 10 N/m C D…

Q: The center of gravity of the 50 kg spool is at G. A cable around the hub of the spool is attached to…

A: Given: The mass of the spool is M is 50 kg. The mass of the block is m is 30 kg. Calculation: The…

Q: Determine the external reaction at the roller support in kN. Select one: a. 280 b. 30 c. 310 d. 120

Q: Two beams at 6 meters in length each are arranged so that the reactions at A, B, and D are the…

Q: The uniform 22-m pole has a mass of 130 kg and is supported by its smooth ends against the vertical…

A: Given- m=130kg W=mg W=130×9.81 W=1275.3N

Q: 600 mm B 200 mm QA A Same capacity 4HD25 600 mm 600 mm 200 mm B 4HD25 100 mm

A: From the above two cases, which has larger positive moment capacity?

Q: 600 N/m A 400N/m 4m. 13m.J 5m 3 2,000 N 1,5 m B

Q: Determine the maximum positive shear in the beam. (in kN) 100 kN Frictionless pin 55 kN/m 60 kN-m V.…

Q: 45 Draw the front view and top view from the following view. 60 15 45 15 2HOLES, DIA 15 15 45 15

A: Q1)

Q: 7) 5 kN 20 kN/m D A -2 m- -3 m- 1 m m

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

2. The light right-angle boom which supports the 4KN cylinder is supported by the three
cables and a ball-and-socket at O attached to the vertical x-y surface. Determine the
reactions at O and the cable tensions.
у
1.2m
1.5 m
D
C
1m
E 1m
A
2.2m
B
0.75 m
0.75 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step by step

Solved in 8 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the horizontal and vertical components of the reaction of the pin A and the reaction of the rocker B on the beam.
7. Determine the horizontal and vertical components of reaction at the pin A and the tension developed in cable BC used to support the steel frame. TI 60 kN B ImIm- -1m- T 3 m A 30 kN - m
2)There is a roller at A and pin support at B. Label the tip of the cantilever "E." The "C" and "D" labels can be disregarded. Use an x-coordinate that starts at the tip of the cantilever and goes to the right. 4 kN/m A B -1.5 m -1.5 m -1.5 m- -1.5m-
20 kN For the frame provided, determine the following: A. The vertical component of the reaction at pin B, kN (in whole number) 20 kN B. The direction of the answer in letter A (down, up, left, or right) C. The horizontal component of the reaction at pin B, kN (in whole number) D. The direction of the answer in letter C (down, up, left, or right) 1m 1m Dr
Determine the value of influence line located at distance 20' for the reaction at C. Show complete solution. hinge 20 84- 10 104
Determine the tension in cables BA and BC necessary to support the 60-kg cylinder shown. 45° Y B D (a)
Determine the value of influence line located at distance 20' for the reaction C.
Thanks for the help Determine support reaction at D
PC =? PI=12+00.00 T = ? E = ? L = ? Tangent, T = Degree, Da= Length, L = Long Chord, LC = MO = ? LC = ? R = 5730 ft I = 1°00'00" PT=? Questions 29-34: Calculate the remaining parts of the circular curve given above: External, E = Middle Ordinate, MO =
•5-21. Determine the horizontal and vertical components of reaction at the pin A and the tension developed in cable BC used to support the steel frame. со B 60 kN -1 m 1m - 1m- 1 m- 3 m Prob. 5-21 30 kN - m
Determine the reaction at support B for the simple beam shown. a. 600N O b. 450N O c. 750N O d. 300N 3 m 400 N/m -3 m- B
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 14i - 16j kN.Note that the reaction force at A acts along the boom because it is a two- force member. Calculate the magnitude of the reaction force at A in kN. 2m 4 m 6 m y A 6m u 7.