Problem 1: The load below is being lifted. And at 4 ft, having constant acceleration from its rest with an upward velocity of 3 ft/sec. The gear at A of the rotating motor drives gear B, which is attached to the rotating drum. Determine the : 1. acceleration of point C on the cable in contact with the rotating drum as the load passes this position. 2. angular velocity and angular acceleration of the gear at The gear at A of the rotating motor drives gear B, which is attached to the rotating drum. C 36 48 12 3 ft/sec L. 4'

Problem 1: The load below is being lifted. And at 4 ft, having constant acceleration from its rest with an upward velocity of 3 ft/sec. The gear at A of the rotating motor drives gear B, which is attached to the rotating drum. Determine the : 1. acceleration of point C on the cable in contact with the rotating drum as the load passes this position. 2. angular velocity and angular acceleration of the gear at The gear at A of the rotating motor drives gear B, which is attached to the rotating drum. C 36 48 12 3 ft/sec L. 4'

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

20 kN For the frame provided, determine the following: A. The vertical component of the reaction at pin B, kN (in whole number) 20 kN B. The direction of the answer in letter A (down, up, left, or right) C. The horizontal component of the reaction at pin B, kN (in whole number) D. The direction of the answer in letter C (down, up, left, or right) 1m 1m Dr
COMPLETE ANSWER AND SOLUTION PLEASE THANKYOU! 1.1
Determine the tension in cables BA and BC necessary to support the 60-kg cylinder shown. 45° Y B D (a)
The boom OAB pivots about point O, while section AB simultaneously extends from within section OA. Determine the velocity and acceleration of the center B of the pulley for the following conditions: 0 = 20°, Ô0 = 5 deg/sec, Ö = 2 deg/sec?, 1 = 15 ft, 1 = 1.6 ft/sec, i = -2.0 ft/sec2. The quantities l and i are the first and second time derivatives, respectively, of the length I of section AB. Express your answers as vectors in the e, and eg directions. B 24' A Answers: VB = i e, + i ee) ft/sec ag = i e, + i eə) ft/sec2
Read the question carefully and give me right solution with clear steps
*4-40. Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power of pulley A is transmitted to pulley B. Determine the horizontal tension T in the belt on pulley B and the x, y, z components of reaction at the journal bearing C and thrust bearing D if 8 - 45°. The bearings are in proper alignment and exert only force reactions on the shaft. 200 min 250 mm 50 N 300 mi 150 mm S0 mm 65 N SO N
Urgent...
The small crane is mounted along the side of a pickup bed and facilitates the handling of heavy loads. When the boom elevation angle is 0 = 37°, the force in the hydraulic cylinder BC is 4.1 kN, and this force applied at point C is in the direction from B to C (the cylinder is in compression). Determine the moment of this 4.1-kN force about the boom pivot point O. The moment is positive if counterclockwise, negative if clockwise. 610 mm 105 mm 285 mm 345 mm B Answer: Mo = kN-m
Please do carefully
Solve for the reaction force Bz.
Solve only- d to g
7.) (2 Points) Neglecting friction and the radius of the pulley. Determine the following: a.) the tension in cable ADB b.) the reaction at C. 150 mm A В 120 N 200 mm 80 mm 80 mm