Q1. Block A has a mass of m kg and is hoisted using the rope-and-pulley system shown. If the collar is moving to the right at V m/s and has acceleration of a m/s at the instant shown, determine the tension in the cable connected to the collar at that instant. c m B. d m A

Q: Solve for the x-component (in mm) of the centroid if that a=2.4, b=2.2, c=4.8, d=9.7, and r=1.6. All…

A:

Q: The force P is applied to the 61-kg block when it is at rest. Determine the magnitude and direction…

A:

Q: The parameter COD is: O a. Usually less in value than the ulitmate BOD b. Usually equal in value to…

A: The parameter COD is: a. Usually less in value than the ulitmate BODb. Usually equal in value to…

Q: Calculate the x-component of B (in N, round-off to 2 decimal places) of the loaded frame. D C 120…

A:

Q: The torque (N-m), T, delivered by a water turbine depends upon the discharge (m³/s), Q, head (m), H,…

A: The number of terms is 6.

Q: y eyebolt X tension rod 12 T Horizontal component for force T =. _N, if T=1000N

A: A loaded beam is given and it has been asked to determine component of forces, please refer step 2…

Q: a+c=2   Calculate the moments of inertia and principal moments of inertia according to the…

A:

Q: Structural mechanics  'method I used was portal method    how do I solve for the following  what…

A: Solution; Using Appropriate method of Analysis

Q: Laplace transformation 1. L{t? + 4t + 5} 2. L{t3 - 4t2 + 4t} 3. L{e e-2t + 4e-3t }

A: For the given Laplace transformations,

Q: Q.9 If n is the ratio of internal and external diameter of a hollow shaft, the ratio of the weight…

A:

Q: Pls answer following question provide a hand written sol.

A: Step 1:Step 2:Step 3:

Q: A negative internal bending moment M causes a beam element to O rotate counterclockwise bend concave…

A: Bending moment at a given section can cause Sagging (concave upward) or hogging (concave downward)…

Q: What is the position vector Ao in ft.

A: Given: Required: Position vector AO

Q: Asap

A:

Q: Example : Replace the three forces acting on the bent beam by a single equivalent force R. Specify…

A:

Q: Substitute: A=4, G=6 H=12 Determine the center of gravity of the built-up section with respect to…

A:

Q: The pipe elbow below discharges water at rate of SN/100 (m/s) into the atmosphere at section 2…

A: The given figure is shown below:

Q: The degree of homogeneity of the function f(x, y) = (x² - 4y²)-¹/2 O A. 1 OB.-1 O C. -1/2 O D. None…

A:

Q: . Which of the following comments about the spacing of the rivets i

A:

Q: Determine the moment of inertia of the shape with respect to the left line

A: The given figure is as follows:

Q: Question 7 7.Value of shear at midspan in Ib. b=3.17 inches h=5.62 inches P= 1657 lb A= 3.75 ft B=…

A: Question is based on the simply supported beam subjected to point load .Magnitude of load and span…

Q: Solve for the internal forces on the beams and columns highlighted as shown using the portal method.…

A:

Q: 1.7 Find the primary dimensions of each of the following terms. pV2 dA, where p is fluid density, V…

A:

Q: A beam is subjected to equal bending moments of M₂ = 2800 N.m. The cross-sectional dimensions are b…

A: The bending moments of Mz = 2800 Nm. The cross-sectional dimensions are b = 150 mm  c = 27 mm d = 72…

Q: Three bars pinned together at B and C and supported by hinges at A and D as shown in Figure 1, form…

A: The given figure is shown below:

Q: 1-sinx/cosx = cosx/1 + sinx. PROVE THE IDENTITY

A: To prove the identity

Q: 1.11 Determine the centroidal moment of inertia for the shapes shown. a. b. k 2 in 1 in- 4 in → 1 in…

A:

Q: 2x1 + x2- 4x3 = 4 Given the system of equations determine whether any two of x1, xX2, Xz 3x 2x2 +…

A:

Q: Q.9 If n is the ratio of internal and external diameter of a hollow shaft, the ratio of the weight…

A:

Q: 3. Using conjugate beam method determine the value of Elō under each concentrated load of the beam…

A:

Q: Determine the value of k that will make the equation exact and sole the resulting differental…

A:

Q: 3 State whether each of the following products is odd, even, or neither. (a) x³ cos2x (d) x²e²x (b)…

A:

Q: * = pw 2 gm/cm3 1 gm/cm³ O 4 gm/cm³ O 3 gm/cm³ ОООС

A: 1 g/cm3

Q: Determine the moment arm of the resultant relative to the origin O. (do) Each space is I fool. 25 lb…

A: Given Data: Let the angles substended by the forces A,B,C be β, θ, and α

Q: a. the polar axis. b. the line 0 2 c. the pole. %3D 7. r = sin 0 8. r = cos 0

A:

Q: The frame is subjected to a concentrated force of F = 1955 lb and a uniform distributed load of…

A: Given, Frame loaded at various points   NOTE : As per guidelines, first 3 parts are solved. Request…

Q: The centroid of the T-section shown is 2.5 inches above the base. What should be the value of b to…

A: Given A T section having centroid 2.5 inch above the base.  Required Value of b

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.