D P y 2 m 55 5 m 5 m 5 m 3 m Crane boom

Q: 1. Draw a Free Body Diagram of Point B and; 2. Solve for the Forces in cable-T1, and cable-T2

A:

Q: The force F in the figure is equal to 10 kN. Determine the following forces: 1. Forces at support BD…

A:

Q: 2) The truss is carrying two masses m (mg=100 N). It is supported by a rope at A and pin support at…

A:

Q: rm steel bar of lengthn IS support at poiht A and B ing two cables as shown in the figure. The bar…

A: To find tension in cable

Q: Consider the following beam ABC, loaded as shown in figure. The cable passes over a small…

A: For given arrangement,W= 10 kNTo find the maximum shear force in the beam AB

Q: Problem 1 The bar supported by a pin at A and a cable at B carries a load of 260 N at C. Neglecting…

A: cable always carry tension so we make the free body diagram for analysis of the given beam. normal…

Q: A system of cables is shown and in a state of equilibrium. Using equilibrium equations, solve for…

A: To find tension in cable AB, BC, CD

Q: Pair of beams (AB) and (CDE) are connected by cable BC and subjected to the concentrated and…

A:

Q: A В y hA hB

A:

Q: THE 10-FT CABLE AB IS ATTACHED TO TWO COLLARS AS SHOWN. THE COLLAR AT A CAN SLIDE FREELY ALONG THE…

A: Given: Length of cable = 10ft Determine- a=?

Q: Cable OA is used to support column OB and exerts a force of 9 kN on the column at O: (a) Determine…

A: Given: a= 5m, b = 3m, c=9m Required : Angle between OA and OC length AC projected component of 9KN…

Q: Example1: The block has a mass of 90 kg and it is supported by the cable system shown in figure.…

A:

Q: The cable AB carries a tension of 470 N. Determine the moment about O (positive if counterclockwise,…

A:

Q: A distributed load that varies from 20 kN/m to 50 kN/m is applied as shown in the figure.…

A:

Q: The rigid beam is supported by a pin at D and cables at AE and CF. If the load P is applied at B on…

A: A rigid beam is hinged at D, the beam can rotate about D but it cannot deform.A load P is applied at…

Q: The 6 m uniform rod as shown below weighs 1000 N. Segment AB and E is 4 m long. The cable acts at a…

A:

Q: ht. The structure is pinned together at points A, B, and C and held in equilibrium by the cable CD.…

A: Given  AC= 16 FT  AB= 8 FT  12000 lbs act at 4 m from A  8000 lbs act at C   Cable CD is at 53 °…

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A: Given: TAB = 9.3 KN , a= 31m, b= 37m, c= 25m, d= 31m Find: TAC= ? , R=?

Q: 3. If the plate is to remain in equilibrium, find the tension for all the three cable that supports…

A: Consider the following free body diagram:

Q: A 1500 kN weight is suspended by three cables AB, AC, and AD as shown. Determine the tension on…

A:

Q: Solve for the Tension Force in kilonewton for the cable supporting the inclined gate. The cable is 6…

A:

Q: 3 m P 3 m B 1.5 mi 3 m E 3 m 1.5 m

A:

Q: over the large pulley. A locking pin at A prevents rotation of the pulley. If µ = 0.4 between the…

A:

Q: The tension in supporting cable AB is T = 750 N. Assume the value of e = 45°. 8. Write this tension…

A:

Q: 2.123 A container of weight Wis suspended from ring A. Cable BAC passes through the ring and is…

A: Given: W = 270 lb The tension is the same in both portions of cable BAC. Solution: Free body…

Q: 1. Determine the maximum weight P that can be held in the position shown just before the machine…

A: To find out the,  1) Maximum weight P that can held in position before the machine begin to tip.  2)…

Q: If the tension in the cable BH is equal to 445 N. a=0,5 m; b-D0,6 m; c=0,6 m; d-D0,2 m; e=1,1 m; C…

A: Draw the figure.

Q: the uniform concrete pole has a mass of 25 tons and is slowly being lifted to a vertical position…

A: Reference : Engineering Mechanics, Tension in cable. Given : Mass = 25 tons = 25000 kg A force P…

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A:

Q: the uniform concrete pole has a mass of 25 tons and is slowly being lifted to a vertical position…

A:

Q: The 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at…

A: Given:- The length of the pole ABC = 6 m  The magnitude of the force acting on pole = P The tension…

Q: 2.1.3

A:

Q: 5. The turnbuckle is turned until the | tension in the cable AB reaches the D value represented by…

A:

Q: The cable AB carries a uniformly varying load. It is connected to a wall at A and is held in…

A:

Q: point in a catenary cable varies with the y-coordinate of the point as T(y)= To + woy. A uniform…

A: Tension force at B, TB = 500 N Weight w0 = 15 N/m ya= 4 m yB = 8 m

Q: 2. The Cable BC carries a tension force of 500 kN. Find the components of the tension force along BA…

A: The given figure is shown below:

Q: You are given the structure and loading below. The load w is 2.4 kips/ft. Find the value of downward…

A: Given, E=29,000 Ksiw=2.4 Kips/ftIAB= 103 in4AAB=4.7 in2Diameter of BC =0.5 in Calculating support…

Q: Consider that the catenary cable in the figure is anchored between supports A and B and is…

A: Consider the free body diagram of the given symmetrical parabolic cable as shown below. d=20 m…

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.