A blanking operation is to be performed to create the part shown below out of 2-mm thick half- hard 405 stainless steel. Provide (a) a drawing showing the punch dimensions; (b) a drawing showing the die dimensions; (c) the blanking force necessary. Note: you will need to translate tensile strength to shear based on the conversion from the text and use material properties from the text as well, tensile strength of 405 can be found in Ch. 6 (Metals). All dimensions noted below are in mm.

A blanking operation is to be performed to create the part shown below out of 2-mm thick half- hard 405 stainless steel. Provide (a) a drawing showing the punch dimensions; (b) a drawing showing the die dimensions; (c) the blanking force necessary. Note: you will need to translate tensile strength to shear based on the conversion from the text and use material properties from the text as well, tensile strength of 405 can be found in Ch. 6 (Metals). All dimensions noted below are in mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Illustrate the four basic operations of volumetric deformation. Indicate next to each illustration the name, type of load applied and the type of tools used.
i need the answer quickly
....
Correct and complete solution please don't copy
Correctly complete the following phrase below: "When a structure is subjected to general loading in two dimensions, Tresca and the Von-Mises criteria are used to... determine the maximum shear stress." Don't Know calculate the principle planes." calculate the deformation in a structure." determine failure of materials that behave plastically."
The engineering stress-engineering strain tensile curve for a stainless steel type 304 alloy is shown. Calculate the constants K and n for the true stress and true strain curve before necking (or = K (&)"). Engineering Stress (MPa) 1000 900- 800- 700- 600- 500- 400- 300- 200- 100- of 0.0 02 0.4 Enginering Strain (mm/mm) 0.6 0.8 1.0
show the work by steps. only HANDWRITTEN answer needed ( NOT TYPED)
Question 4 Save Answer You do a series of tensile tests on plates of a magnesium alloy that have been subjected to prior cold rolling to true plastic strains of 0.1, 0.2 and 0.3. The resulting true stress-true strain curves are shown below (including a zoomed in version expanding on the small strain region). It is reasonable to approximate the the 0.2% offset yield strength of the magnesium as ✓ MPa for 0.2 and ✓ MPa for 0.3. Assuming the yield strength is ✓ MPa for 0.1 plastic strain, proportional to the square root of the prior true plastic strain results in a hardening coefficient of approximately k= MPa. Hence, we can predict that we need a prior plastic strain of approximately True Stress (MPa) True Stress (MPa) True Stress (MPa) 250 200 150 100 50 0 0.00 250 200 150 100 50 0 0.00 250 200 150 100 50 0 0.00 Ep = 0.1 0.01 Ep=0.2 0.01 Ep=0.3 0.01 0.02 True Strain 0.02 0.03 0.02 0.03 True Strain 0.03 0.04 0.04 0.04 True Stress (MPa) 0.05 0.000 0.001 True Stress (MPa) Ep=0.1 True…
Q4: Proof the validity true strain additive feature in compression deformation?
An electric car manufacturer is looking to utilize some stock AISI 8740, hot rolled steel bars that are around 2 inches in diameter for their conveyor system that is being set up to start producing their own batteries. The data sheet shows the the bars to have 132,000 psi tensile strength, 87,500 psi yield strength, and 16.7% elongation. A hardness of 262 Bhn allows it to be finish machined after heat treatment. They keep their workspace at 70°F. What is the working endurance strength, Se? 39,750 psi 28,562 psi 42,500 psi 33,400 psi
Case Study Calculate the Tensile Toughness Tensile toughness measures the total energy absorbed prior to fracture and is different from fracture toughness and impact toughness. Fracture toughness measures the resistance to fracture when a flaw (i.e. crack) is present in the material. Since it is nearly impossible and costly to manufacture materials with zero or near zero defects, fracture toughness is a major consideration for all structural materials. Impact toughness measures a materials ability to withstand an impact blow (i.e. high strain rates) and is particularly important in assessing the ductile-to-brittle transition behavior (more details later). Impact toughness is also commonly referred to as notch toughness. The tensile toughness can be estimated using the stress-strain curve by measuring the area under the curve (both the elastic and plastic regions). Tensile Toughness = f Stress, σ Ty- Ey Efracture ETS Ur Ey Efracture o de = U₁ + SETS o de + Sefracture o de Ey Ey o de =…
A 250 mm diameter circle is etched on a 400 mm x 400 mm x 12 mm piece of sheet metal. The elastic modulus is 190 GPa and Poisson's ratio is 0.3 for the material If stresses of 40 MPa and 75 MPa are applied in the x and y directions respectively, calculate the following: a) Change in sheet thickness, i.e. find At. Hint engineering and true strain are equal in the elastic regime. b) Sketch the shape of the circle after deformation on the figure below c) What is the elastic strain energy in the thickness direction only?