A compound die will be used to blank and punch a large washer out of 6061ST aluminum alloy sheet stock 4.50 mm thick. The outside diameter of the washer is 60.0 mm and the inside diameter is 25.0 mm. Determine the punch and die sizes for the blanking operation. Determine the force required to perform the blanking and punching operation, assuming that the punches are staggered so that punching occurs first, then blanking. The aluminum sheet metal has a tensile strength = 310 MPa. Consider a clearance allowance value of 0.060.

A compound die will be used to blank and punch a large washer out of 6061ST aluminum alloy sheet stock 4.50 mm thick. The outside diameter of the washer is 60.0 mm and the inside diameter is 25.0 mm. Determine the punch and die sizes for the blanking operation. Determine the force required to perform the blanking and punching operation, assuming that the punches are staggered so that punching occurs first, then blanking. The aluminum sheet metal has a tensile strength = 310 MPa. Consider a clearance allowance value of 0.060.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please I need an answer within half an hour
The engineering stress-engineering strain tensile curve for a stainless steel type 304 alloy is shown. Calculate the constants K and n for the true stress and true strain curve before necking (or = K (&)"). Engineering Stress (MPa) 1000 900- 800- 700- 600- 500- 400- 300- 200- 100- of 0.0 02 0.4 Enginering Strain (mm/mm) 0.6 0.8 1.0
A figure shown below is to be blanking through a blanking die The material is 4mm thick stainless steel (half hard) with Ac =0.075. Determine the dimensions of the blanking punch and the die opening
The stress and a pipe varies jointly with the internal pressure and the diameter of the pipe, and inversely with the square of the thickness of the pipe. The stress is 200 pounds per square inch when the diameter is 4 inches, the thickness is 0.40 inches, and the internal pressure is 25 pounds per square inch. Find distressed wood and internal pressure is 50 pounds per square inch if the diameter is 10 inches and a thickness is 0.50 inches. Define variables Stress in pipe Internal pressure of pipe Diameter of pipe Thickness of pipe Find k Update formula Answer question
This is not writing assignment question.
answer is not correct, it should be 13.89 MPa
- Sketch the principle of a hydraulic press. Explain the principle of the amplification of the force. - When the primary piston is moving for Ax, what is the distance the secondary piston Ax will move?
: Determine the force necessary to punch a 10 mm dia. Hole in a 20 mm thick mild steel plate, if the shearing strength of mild steel is 10 N/ mm2. Also, state the nature and magnitude of the stress in the punch.
A 1-in diameter hole is to be punched through a 1/8-in thick annealed titanium-alloy Ti-6Al-4V (grade 5, annealed) sheet at room temperature. Estimate the force required for the punching operation. Show your work and list any values you reference/use. Hint: Use the equation F=T*L*Shear Strength
How will you calculate the value of the slope of this best-fit line? How will the value of the slope help you identify the unknown material that the cylinders are made of?
!
Determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading for a given rectangular block with the following data: 4 inches long in the x direction, 2.5 inches long in the y direction, and 3.5 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 52 kips tension in the x direction, 68 kips compression in the y direction, and 49 kips tension in the z direction. Given v = 0.28 and E = 30 x 10° psi, O a. 265.23 kips O b. 255.80 kips Oc 220.25 kips O d. 246.56 kips