A beam 150 mm x 300 mm is prestressed by a straight cable carrying prestressing force of 250 kN at an eccentricity of 40 mm. The beam supports a udl of 7.2 kN/m including self weight of beam. If span of beam, grade of concrete and unit weight of concrete are 5 m, M50 and 24 kN/m3 respectively then the load factor against cracking is

A beam 150 mm x 300 mm is prestressed by a straight cable carrying prestressing force of 250 kN at an eccentricity of 40 mm. The beam supports a udl of 7.2 kN/m including self weight of beam. If span of beam, grade of concrete and unit weight of concrete are 5 m, M50 and 24 kN/m3 respectively then the load factor against cracking is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Concrete beam.
At the limit state of collapse, an RC beam is subjected to flexural moment 200 kNm, shear force 20 kN and torque 9 kNm. The beam is 300 mm wide and has a gross depth of 425 mm, with an effective cover of 25 mm. The equivalent nominal shear stress (t) as calculated by using the design code turns out to be more than the design shear strength (T) of concrete, The equivalent shear force and equialent flexural moment ?
For the below given beam: a) Determine the cracking distributed load. b) Determine the stress in concrete and steel under service load if WDL = 15 kN/m; WLL = 10 kN/m Materials: C25; S420 40 mm 1.8 m 560 mm 300 mm
Q3) The reinforced concrete beam having span of 6 m carrying total design load of 30.6 kN/m as shown in figure Q3. Using following design data, design main reinforcement for the beam. Design data: The characteristic strength of reinforcement steel (f,) = 500 N/mm? The characteristic strength of concrete is (feu) = 30 N/mm². Diameter of tension reinforcement is 25 mm, Diameter of compression reinforcement is 16 mm if required. Diameter of shear link 8 mm Concrete cover 40 mm, 30.6 kN/m h-370 mm b- 230 mm Section A-A
A rectangular concrete beam 277 mm wide and 495 mm deep is simply supported over a span of 8.37 m. the beam is reinforced with straight tendons situated 59 mm above the bottom of the beam under a prestressing force of 387 kN. Concrete weighs 23.36 kN/m3 with modulus of elasticity Ec=13,814.76 MPa. Assuming tension concrete does not crack, what is the midspan deflection due to the given loads. (Include the sign if it is negative) Please avoid rounding off values during the course of solution proper as much as possible. Always write your answer in 4 decimal places
A concrete beam of rectangular cross section 250 mm x 500 mm is prestressed with a force of 500 KN at an eccentricity of 125 mm. The maximum compressive stress in concrete is
Problem- A doubly reinforced rectangular concrete beam has a width of 30mm and an effective depth of 500 mm. The beam is reinforced with 2200 mm² of steel in tension and 628 mm² of steel in compression. The effective cover for compression steel is 50 mm. Assume that both tension and compression steel yield. The grades of concrete and steel used are M20 and Fe250, respectively. The stress block parameters (rounded off to first two decimal places) for concrete shall be as per IS 456 : 2000. Find the depth of neutral axis.
PROBLEM TO SOLVE: 600 mm 400 mm 6-25mm diam. 90 mm Using fc' = 28 MPa, Mmax = +320 kNm Determine the following: a. Cracking Moment (kNm) b. Compressive Stress felt by concrete (MPa) c. Tension Stress felt by the tension bars (MPa) d. Moment of Inertia under critical condition e. Demand Capacity Ratio of Concrete under Compression Stress f. Compression force on concrete (kN) g. Distance of the compression concrete force from the neutral axis (mm)
A reinforced concrete beam experiences a load as shown. It has a base of 350 mm, and an effective depth of 600 mm, with 4 – 25 mm diameter rebars. The concrete has a compressive strength of 27.6 MPa, Determine the maximum distributed load that the beam can carry. Assume that the allowable stress in steel is 167 MPa (instead of 160 MPa). w 1.5 m 10 kN 1.5 m 5 m