Q3) The reinforced concrete beam having span of 6 m carrying total design load of 30.6 kN/m asshown in figure Q3. Using following design data, design main reinforcement for the beam.Design data:The characteristic strength of reinforcement steel (f,) = 500 N/mm?The characteristic strength of concrete is (feu) = 30 N/mm².Diameter of tension reinforcement is 25 mm,Diameter of compression reinforcement is 16 mm if required.Diameter of shear link 8 mmConcrete cover 40 mm,30.6 kN/mh-370 mmb- 230 mmSection A-A

The most important reason for providing the doubly reinforcement beam is that they provide safety…

Answered: O The reinforced concrete beam having…

O The reinforced concrete beam having span of 6 m carrying total design load of 30.6 kN/m as shown in figure Q3. Using following design data, design main reinforcement for the beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the longitudinal and shear reinforcement for a 275 mm square, short- braced column which…

Q: Given: Beam Dimensions, bx h=350mm x 450 mm Effective Cover to centroid of steel reinforcement = 75…

Q: Problem 2: For the given beam section below find the design moment (Mn) whereas f'c = 4 ksi, fy = 60…

A: Given doubly reinforced beam with values,Width of the beam, b= 12''Effective depth,…

Q: : A simply supported beam with 5 m span. Find maximum factored uniformly distributed load "Wu" that…

Q: design a Pined Reinforced Concrete frame supported equally by two columns which should satisy the…

A: It is design a Pined Reinforced Concrete frame supported equally by two columns which should satisfy…

Q: ). Determine the flexural reinforcement for the simply reinforced concrete Isolated T-Beam own in…

Q: A W 21 x 48 beam is simply supported on a span 7 m. The beam is laterally supported at its ends and…

A: W 21 x 48 beamSpan = 7 mService dead load = 7 kN/m (including the weight of the beam)Service live…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

Q3) The reinforced concrete beam having span of 6 m carrying total design load of 30.6 kN/m as
shown in figure Q3. Using following design data, design main reinforcement for the beam.
Design data:
The characteristic strength of reinforcement steel (f,) = 500 N/mm?
The characteristic strength of concrete is (feu) = 30 N/mm².
Diameter of tension reinforcement is 25 mm,
Diameter of compression reinforcement is 16 mm if required.
Diameter of shear link 8 mm
Concrete cover 40 mm,
30.6 kN/m
h-370 mm
b- 230 mm
Section A-A

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A short, braced column is subjected to an ultimate applied axial load of 3000 kN and a nominal moment only. Using the design data given: Design the main steel reinforcement with minimum size of square column to carry the load without failure Design Data: Characteristic strength of concrete fcu = 40 N/mm2 Characteristic strength of reinforcing steel fy = 460 N/mm2 Clear height between the end restraints about both axes = 5.0 m
Using the alternate design method, design (the dimension) of a 4 m simply supported rectangular beam for flexure, when it will be subjected to a 25 kN/m dead load, excluding its own weight, and a live load of 30 kN/m, under the following conditions: concrete unit weight, Y = 23.5 kN/m³ fc' = 28 MPa fy = 420 MPa If d₁ = 32 mm is used, how many bars are needed for its reinforcement?
The figure below shows an industrial composite floor plan comprising 225 mm thick RC slab, supported on steel beams and column. The slab is expected to support the finishes and ceiling loads of 1.2 kN/m? in addition to the imposed load of 4.5 KN/m?. Assuming the unit mass of both the steel beam and 3m hight columns are 75 and 50 kg/m run respectively. (a) Estimate the design loads acting on beams B1-C1, B2-C2 and B1-B3 and columns B1 and C1. (b) Use the load estimated in (a) above; (i) Design the slab in one of the panels using the following material strengths; fcu = 30 N/mm? and fy = 500 N/mm? %3D (ii) Design the beam B2 - C2 using structural steel member with permissible bending stress = 460 N/mm2 3 4 m (2 4 m 4 m 8 m (A B
Example AT beam R.C. floor system consists of 120 mm thick slab supported by beams at 3 m centre to centre. The effective width and depth of web is 300 mm x 580 mm as shown in Fig. 3.13. Main reinforcement consists of 8 bars of 20 mm diameter. The grade of concrete and steel used are M20 and Fe 415 respectively. Determine the moment of resistance of the T beam, if it is used as simply supported beam of span 3.6 m. by 1620 mm. 300 mm 580 mm 120 mm X
Referenced concrete Number of student 1
if the given beam section is used for a simply supported beam 6.5 m span, using f'c=21MPa and fy=280MPa. 1. Calculate the ultimate shear strength of concrete (kN) using simplified formula of NCSP 2015. 2. calculate the nominal shear strength of the stirrups, Vs, in kN. 3. calculate the design sectional shear strength of the beam in kN.
Please answer with clear detail and explain each step by step process
A reinforced concrete beam section is "b" wide and "h" deep. It is to be reinforced with the given diameter and number of pieces below, stirrups is 10 mmØ with clear concrete covering of 40 mm. Consider f'c = 32 MPa and fy = 415 MPa. 1) If the beam is reinforced with 4 - 25mmØ tension steel only, calculate the tension steel strain et. 2) If the beam is reinforced with 6-28mmØ tension steel (in two layers of 3 bars each with 25 mm clear distance between layers), calculate the tension steel strain et. 3) Calculate the flexural strength of the beam in question 2. 4) Determine the total unfactored dead load and live load using the result in problem 3 that the beam can carry if dead load is 30% of the total live load. Use "L" as total beam length. Assume that the beam is simply supported. 5) Determine the superimpose dead load that the beam can carry from the resut in problem 4 if concrete weighs 23.6kN/m3. b 380mm h 520mm L 5.70m