A bar of titanium alloy of length 120mm and square cross – section, 7.5 mm x 7.5 mm, is pulled axially by a force of 15 kN. Find the percentage decrease in thickness if E = 106 GN/m2 and v = 0.33 m/s. V= velocity A bar of aluminum alloy of rectangular section75 mm x 20 mm and 800 mm long is stretched by an axial force of 150 kN. Find the volumetric strain, the actual change in volume and the percentage reduction in cross – sectional area of the bar. Take E = 70 GN/m2 and v = 0.34 m/s.V=velocity

Q: Solve the stress tensor at the location of strain gauge (red dot). Find the principle stresses and…

A:

Q: A large thin rectangular plate is subjected to certain traction boundary conditions on its thin…

A: Given :  φ(x,y)=Ax4+Bx2y2+Cy2

Q: Example 3.2 A 60mm diameter solid shaft has a strain gauge mounted at 65° to the axis of the shaft.…

A: Shear strain is defined as a ratio of the shear stress to the modulus of rigidity.

Q: A circular solid piece of rock is tested in a compression testing rig to examine its stress/strain…

A: Sample diameter, d=6 inchesSample original length, L=12 inchesCompression load, P=10000 lbfReduction…

Q: A 1.25 m long cable has a diameter 3.50 mm with a Young's Modulus, E, of 9.75 x 10⁹ N/m². When the…

A:

Q: Given is a thin-walled tube with the following data: Wall thickness- 2mm ABC is a sector with a…

A:

Q: Ex Yxy Yyx 3.3.2 Drawing the Mohr's Circle Example: - Ex = 70με &y = 40με Yxy = 60 με لاوه لان Yyx…

A: Given data:- εx=70 με (Tension) εy=40 με (Tension) γxy=60 με (Positive) To draw:-Mohr's Circle

Q: MPa . Assumin H/m² and Poisso hange in diamet

A: Given data  Dia of pressure vessel =650 mm Internal pressure = 14.7 Modulus of elasticity = 200 GPa…

Q: Stress (MPa) Graph 1 - Stress/Strain plot 400 320 300 200 100 0 (a) 51.472kN (b) 205.89kN (c) 25735N…

A:

Q: With the force P appliced on a member, the stress distributions at different cross sections are…

A:

Q: Rockwell hardness . figure 6.19 Rockwell hardness Tensile strength = 0 MPA Tensile strength = 0 ksi…

A: (a)

Q: A copper wire 3m long and 1mm^2 in cross-section is fixed at one end and a weight of 10 kg is…

A:

Q: Explain the phases shown in the attached image of a stress strain cureve for 0.15% carbon steel

A:

Q: 5. A solid steel disk E-200x10^9 N/m^2 start rotation from the rest with constant acceleration. When…

A: given,  Radius R =2 m Final angular velocity , ω0 =2500 rad/s Young's modulus of aluminum  , EAl =…

Q: A copper wire has a radius of 3.5 mm. When forces of a certain equal magnitude but opposite…

A:

Q: A straight length of copper steam pipe 450mm long connects two components. Find the stress in the…

A: According to the given data E=103Gpa L=450mm α=1.7x10-5/°C ∆T=140°C δ=0.8mm We need to find Stress…

Q: A steel (E=30x106 psi) rod 10m long and 5cm in diameter is subjected to a compressive force of…

A:

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.