A ball of mass M = 1.30 kg and radius r = 4.50 cm is attached to one end of a thin, cylindrical rod oflength L = 14.0 cm and mass m = 0.880 kg. The ball and rod, initially at rest in a vertical position andfree to rotate around the axis shown in the figure below, are nudged into motion.LmM(a) What is the rotational kinetic energy of the system when the ball and rod reach a horizontalposition?J(b) What is the angular speed of the ball and rod when they reach a horizontal position?rad/sV(c)Vfreefall(c) What is the linear speed of the center of mass of the ball when the ball and rod reach ahorizontal position?m/s(d) What is the ratio of the speed found in part (c) to the speed of a ball that falls freely throughthe same distance?

Given, Mass of the ball, M=1.30kg Radius, r=4.5cmr=4.5×10-2m Length of the rod, L=0.14m Mass of the…

Answered: A ball of mass M = 1.30 kg and radius r…

Similar questions

A wheel with a radius of 0.23 m and a mass of 7.31 kg spins about its axis at 6.53 radians per second. What is the kinetic energy of the wheel in J? Treat the wheel as a cylinder of constant density.
Consider a basketball player spinning a ball on the tip of a finger. If a player performs 1.95 J of work to set the ball spinning from rest, at what angular speed ? will the ball rotate? Model a basketball as a thin-walled hollow sphere. For a men's basketball, the ball has a circumference of 0.749 m and a mass of 0.624 kg .
Energy of a Bullet Dissipated by Plywood. As part of a criminal investigation, you need to determine how much of a bullet's energy is dissipated by a 0.500-inch piece of plywood. You construct a device that consists of three disks that are separated by a distance d = 0.850 m and rotate on a common axis. The bullet is fired through the first disk (a few inches above its center), which is composed of a light plastic that has a negligible effect on the speed of the bullet. The bullet then passes through the second disk, which is composed of 0.500-inch plywood. Finally, the bullet strikes the third disk, where it becomes embedded. The disks rotate with an angular velocity of w = 86.0 rad/s. The angular displacement between holes in the first and second disks is A012 = 0.269 rad, and the angular displacement between the holes in the second and third disks is A023 = 0.286 rad. If the mass of the bullet is 12.0 g, find (a) the initial speed of the bullet and (b) the energy dissipated by the…
a 40kg disk with a radius of 30 cm is spinning around a fixed vertical axis with an angular speed of 10 rad/s. How much work must be done on the disk to bring it to an angular speed of 20 rad/s? a)270J 200J 150J 100J e)40J
In the figure, a wheel of radius 0.234 m is mounted on a frictionless horizontal axis. The rotational inertia of the wheel about the axis is 0.586 kg-m2. A massless cord wrapped around the wheel's circumference is attached to a 4.00 kg box. The system is released from rest.When the box has a kinetic energy of 4.00 J, what are (a) the wheel's rotational kinetic energy and (b) the distance the box has fallen? Assume free-fall acceleration to be equal to 9.81 m/s2. M (a) Number Units (b) Number Units
A bicycle wheel with a radius of 350 mm and a mass of (2.40x10^0) kg is spinning freely on a work stand at a rate of 2.0 rev/sec when a (1.0000x10^0) kg kitten jumps on it radially, holds on and starts spinning around. What is the new rotational velocity of the wheel in units of rev/s? Treat the wheel as a thin hoop. Give your answer with three significant figures.
A 20-kg piece of steel pipe that is 20 cm in diameter, 80 cm long, and 1 cm thick is rolling toward you at a speed of 3.0 m/s. (a)What is the magnitude and direction of the pipe’s angular velocity vector w? (b)What is the pipe’s rotational energy? (c) What is its total energy K + Urot?
A 100 g disk with a diameter of 10 cm rotates about an axis through its center of mass with 0.2 J of rotational kinetic energy. What is the speed of a point on the rim of the disk?
Trucks can be run on energy stored in a rotating flywheel, with an electric motor getting the flywheel up to its top speed of 683 rad/s. One such flywheel is a solid, uniform cylinder with a mass of 535 kg and a radius of 1.2 m that rotates about its central axis. What is the kinetic energy of the flywheel after charging? If the truck uses an average power of 8.4 kW, for how many minutes can it operate between chargings?