The rigid body shown in the figure consists of three particles connected by massless rods. It is to be rotated about an axis perpendicular to its plane through point P. If M = 0.28 kg, a = 22 cm, and b = 34 cm, how much work is required to take the body from rest to an angular speed of 5.3 rad/s? Number i Units 2M b a M P a 2M

The rigid body shown in the figure consists of three particles connected by massless rods. It is to be rotated about an axis perpendicular to its plane through point P. If M = 0.28 kg, a = 22 cm, and b = 34 cm, how much work is required to take the body from rest to an angular speed of 5.3 rad/s? Number i Units 2M b a M P a 2M

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Rotational kinetic energy: A uniform solid sphere of mass M and radius R rotates with an angular speed w about an axis through its center. A uniform solid cylinder of mass M, radius R, and length 2R rotates through an axis running through the central axis of the cylinder. What must be the angular speed of the cylinder so it will have the same rotational kinetic energy as the sphere? 2w/√5 4w/5 ○ w/√√5 2w/5 √215 W
While spinning down from 500.0 rpm to rest, a solid uniform disk does 51 KJ of work. If the radius of the disk is r=400mm what is it's mass?.
The thin uniform rod in the figure has length 2.0 m and can pivot about a horizontal, frictionless pin through one end. It is released from rest at angle 8-50° above the horizontal. Use the principle of conservation of energy to determine the angular speed of the rod as it passes through the horizontal position. Assume free-fall acceleration to be equal to 9.83 m/s². Number i Units
A system of point particles is shown in the figure. Each particle has mass 1.0 kg and they all lie in the same plane. If the system rotates at 10 rev/s, what is its rotational kinetic energy? 40 cm axis 20 cm 60 cm O 1.1 x 103 . O 2.2 x 103 ) 3.4 x 103 J O 4,4 x 103 ) 5.2 x 103 J
The figure shows a rigid assembly of a thin hoop (of mass m = 0.24 kg and radius R = 0.16 m) and a thin radial rod (of length L = 2R and also of mass m = 0.24 kg). The assembly is upright, but we nudge it so that it rotates around a horizontal axis in the plane of the rod and hoop, through the lower end of the rod. Assuming that the energy given to the assembly the nudge is negligible, what is the assembly's angular speed about the rotation axis when it passes through the upside-down (inverted) orientation? Number i Rod Hoop ! Rotation axis Units
A 85.0 kg hoop rolls along a horizontal floor so that its center of mass has a speed of 0.110 m/s. How much work must be done on the hoop to stop it? Number i 1.03 Units
A uniform rod of mass 0.7 kg and length 2.1 m is free to rotate about one end. If the rod is released from rest at an angle of 60° with respect to the horizontal, what is the speed of the tip of the rod as it passes the horizontal position? 60° m/s Question Help: M Message instructor Submit Question
NE Chapter 10, Problem 062 Z Your answer is partially correct. Try again. In the figure, three 0.07 kg particles have been glued to a rod of length L = 5 cm and negligible mass and can rotate around a perpendicular axis through point O at one end. How much work is required to change the rotational rate (a) from 0 to 20.0 rad/s, (b) from 20.0 rad/s to 40.0 rad/s, and (c) from 40.0 rad/s to 60.0 rad/s? (d) What is the slope of a plot of the assembly's kinetic energy (in joules) versus the square of its rotation rate (in radians-squared per second-squared)? Axis (a) Number Units 0.0010110 (b) Number Units 0.030 (c) NumberTo.050 Units (d) Number UnitšT kg-m 2 m Click if you would like to Show Work for this question: Open Show Work em
The rigid body shown in the figure consists of three particles connected by massless rods. It is to be rotated about an axis perpendicular to its plane through point P. If M = 0.41 kg, a = 35 cm, and b = 53 cm, how much work is required to take the body from rest to an angular speed of 5.8 rad/s? M 2M Number Units J
A flywheel is a solid disk that rotates about an axis that is perpendicular to the disk at its center. Rotating flywheels provide a means for storing energy in the form of rotational kinetic energy and are being considered as a possible alternative to batteries in electric cars. The gasoline burned in a 189-mile trip in a typical midsize car produces about 1.12 x 10⁹ J of energy. How fast would a 48.7-kg flywheel with a radius of 0.290 m have to rotate to store this much energy? Give your answer in rev/min. Number Units
7 kg 3 kg 53° 49° There is no friction in the system above except between the rope and the pulley so that the rope does not slip on the pulley. The pulley is a uniform spherical shell with a mass of 1.43 kg and radius of 12 cm, and the rope does not slip on the pulley. The system is released from rest. Use work-energy principles to determine how much kinetic energy does the smaller mass have after moving d = 2.3 meters parallel to the ramp? K =
A flywheel is a solid disk that rotates about an axis that is perpendicular to the disk at its center. Rotating flywheels provide a means for storing energy in the form of rotational kinetic energy and are being considered as a possible alternative to batteries in electric cars. The gasoline burned in a 340-mile trip in a typical midsize car produces about 4.31 x 10 J of energy. How fast would a 34.8-kg flywheel with a radius of 0.577 m have to rotate to store this much energy? Give your answer in rev/min.